Models > YACR4503SFW6 > Instructions

YACR4503SFW6 Amana Range - Instructions

Jump to:

All Instructions for the YACR4503SFW6
61 - 75 of 196
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Sean from LISLE, NY
Parts Used:
WP3149400
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Could not control temperature for 8" burner (front right).
The repair was easy. I unplugged the stove, removed back panel, pulled knob and removed 2 screws to remove switch. Unplugged old switch, plugged in new one and installed the 2 screws for switch. Had to snap off stem for new switch to fit knob (easily done with pliers with provided notch). Put knob and back panel back on. Total time, maybe 20 minutes.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
corey from SHAKER HEIGHTS, OH
Parts Used:
W10856603
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Sparks flying out of the oven, broiler element melting
First Things first, unplug unit, remove rear cover with Phillips head screwdriver, disconnect, wires from broiler element which is the top, one, open oven, unscrew top screws first, then two at the back, wiggle out element, then reverse Steps , test repair before putting cover back on. Then ta-da, you saved yourself a $300. Service call to the appliance repair guy.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
chris from HILTON HEAD, SC
Parts Used:
W10856603
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Broiler element burned out
After doing a YouTube search. I successfully completed the repair by easily diagnosing the issue with the element.
I watched a video about 5 most common problems with whirlpool broiler elements.
The first being to inspect the element for damage. I found a small section that appeared to be rough and had a raised bump.
I decided to order a new element because the oven is older and it wouldn’t hurt to install a new one even if this wasn’t the issue.
Once the part arrived, which it did quickly, I followed the video instructions. It was easy and straight forward. I completed the task in under thirty minutes. It was very simple and I now have a functional broiler element.
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rosalind from APOLLO, PA
Parts Used:
WPW10181986
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
the oven temperature was not working right. I installed a new oven sensor. Works get now
Watch the video...
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from HARMONY, MN
Parts Used:
WPW10181986
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
temp level uneven
after watching the video, installed the temp sensor. Super easy
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ralph from MARION, OH
Parts Used:
WP3149400
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Burner didn’t work right
Replaced switch. Works right now.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sabrina from FREMONT, CA
Parts Used:
WPW10196406, WPW10196405
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Used part
Lift burners out of plug discard old drip pans replace new drip pans into plugs and done .
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steve from GREENBRIER, TN
Parts Used:
WP3148952
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
could not control the temp of the element
take off back panel, simply unplug the old switch and plug in the new one. Simple
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Norman from Newport, NC
Parts Used:
814399
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
burner plug broken
Cut wires removed old plug,new plug in wire nuts on.Put heat on shrink tube done.
Less than 30 min.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
MICHAEL from FOUNTAIN INN, SC
Parts Used:
WP3148952
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Cooktop on and cooktop hot indicator lights stayed on.
Range surface element control switch was bad. Replaced the switch and every thing works fine. Removed two Philips head screws in front and two Philips head screws in back of the range. Pulled the front panel away from the back of the range with the power off of course. Unplugged the wires and removed the two screws that held the switch in. Replaced the switch and refastened the control panel. Tested the switch and every thing worked fine.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
RICHARD from DELTONA, FL
Parts Used:
WP3149400
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
8" FRONT BURNER STAYED ON HIGH HEAT/WOULD NOT REDUCE TEMPERTURE
REMOVE BACK OF RANGE, REMOVE BURNER KNOB. REMOVE SWITCH CONTROL REMOVE WIRES. REPLACE WIRES ON NEW SWITCH. INSERTED ALL WIRES REPLACE NEW SWITCH RE REPLACE ALL SCREWS. CHECK SWITCH. TURN BRAKER BACK ON. CHECK SWITCH FUNCTION. ALL IS FINE. PUT BACK ON RANGE SCREW IT IN PLACE. MOVE RANGE BACK IN IT POSITION.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Darin D from MASON, TN
Parts Used:
W11182108
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
No heat in oven
Broiler worked, Oven did not.
Remove two Phillips screws, unplug element, reverse for installation.
Did not correct the issue.
After replacing the oven temperature control also, it turned out the control board was the issue all along.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brian from YORK HAVEN, PA
Parts Used:
WP3149400
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Right front burner would only stay on high
Turned off breaker, pulled stove from wall, took off knob, unscrewed and pull off backing from stove, unscrewed heat control part, unplugged wires, plugged into new part, installed part, replaced stove backing, replaced knob, pushed stove back in place and turned on breaker. It worked fine.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Edward from TAYLORS, SC
Parts Used:
WP3149400
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
surface element out
Unplug from outlet and top remove back section of range and unplug wiring from switch, remove knob and unscrew two screws and remove old switch. Install new switch reinstall screws and plug switch plugs into new switch (will only go on the correct way). reattach back and plug into outlet. All done and surface element works perfectly.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lowell from Hardin, KY
Parts Used:
WPW10196405, WPW10196406
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Couldn't find correct drip bowls that fit.
Removed old drip bowls, removed burners installed new drip bowls,installed burners. They fit perfect and I received them two days after ordering.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the YACR4503SFW6
61 - 75 of 196