ACF3355AW (PACF3355AW0) Amana Range - Instructions

It was really easy because I read information on your site. I only had to unscrew 3 screws, remove the old spark ignition electrode, replace the new one and then screw the 3 screws back. It was great

I turned off the gas at the back of the oven & unpluged it. I then removed the 2 screws that secure the oven bottom plate to the oven. Once removed, that exposes the oven burner & igniter. There are 2 sscrews that secure the igniter to the burner; remove those screws, & pull the igniter wires out, to expose the connector. Unplug the connector, & the igniter is free. Just reverse the process with the new igniter.

I first tested the broiler and that worked so we determined that the igniter on the bottom was not working. I removed the grill and then removed the igniter ( it is attached with two screws and unplugs from the back of the oven. I then looked up the part we needed on the part select website by model number and found the exact one ( the picture was very helpful) We received the part in one day installed it and the oven is working better than ever.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Plug in the element put the wires back in the hole and screws the element on and that was it. Worked great.

The biggest problem was gettng the correct ignitor, seems there are two. The first ignitor was the wrong one (I do not remember seeing any reference to which on the order page), but once I had the correct one my biggest issue was to get the stove out far enough for me to get behind it to take the cover off. Six scews and a disconnect and a repeat to replace and done. I must mention that the service rep was extremely helpful and easy to deal with and there was no language issue. The replacement part came in two days. I would definitely order more parts from this company

Removed plate at bottom of oven and unscrewed ignitor. Tipped oven forward and removed tiny back panel to reach plastic socket that disconnected ignitor from oven. Pulled ignitor out and awaited replacement part and did reverse steps. Oven ignitor worked right away.

For stovetop I ordered part and removed sheet metal screws from oven rear top panel after appliance was pulled from wall, gas and electrical disconnected. I pulled old spark ignitor module out and transferred colored wires to new module and snapped that into place. Replaced oven and presto, stovetop ignitors worked immediately.

i got the right part from u fast del.and had it fixed in 15 min. was very happy withu service thank u will buy more parts from u when i need them it was the same part i took out

Removed the racks inside the oven then (2) screws that hold the bottom cover. Once the cover was off I exposed the burner element. I Removed (2) small Philips screws that held the unit. I removed electrical plug and the unit was out. I replaced the part and put everything back together. This was a very simple job took me about 10 minutes to complete. gas company wanted to charge $130 just to come out and look at. I saved some good cash.

Remove two phillips screws, lift the burner head up and remove the wire from the electrode. DO NOT DROP THE WIRE!!! It will fall into the stove top, adding much more time and frustration to this very simple repair. Reverse these steps to complete the repair.

Replaced both the broiler (top) oven ignitor and bake (bottom) oven ignitor! Easy to do, no need to call a repair person on this job!

Very simple, cleaned out what was remaining of the old rubber feet and just pushed these in. I didn't bother glueing them in as I didn't feel they would fall out. If they do, I'll go out and obtain the glue that is mentioned by others in this thread. Very satisfied.

I am sure I saved a bunch of money for an outside repair. It was so simple I was embarassed that I did not attempt the repair sooner. Removed two screws from old burner head lifted it up unplugged the electrode wire replaced with new burner head put the two screws back in place and I was finished.

got new horizontal igniter from Parts Select pulled stove out from wall unplugged old igniter took out bottom oven pan loosened two screws. used same two screws to put new igniter in place, put back bottom oven pan pushed bake button on front of oven and the old was lioke new again

Took off the bottom panel of the oven two screws then unpluged old igniter then pluged in the new igniter, replaced the bottom panel and that was all. I didn't even have to take the oven door off. Repair was done in less that 5 min.

I'm a girl, blonde, and fixed it! Oven just turned 10 in July. I removed oven racks, then used screw driver to remove two screws for the lower panel. Used screw driver to listen the two screws that hold igniter in place, then wrench to remove. Pulled wires out from hole in back of oven, unplugged old igniter, used needle nose pliers to hold wires in place from slipping back through hole, plugged in new, pushed wires back in, screwed it in, turned oven on to make sure igniter worked, it glowed, turned off, replaced lower panel, turned oven on again to let it light up, it did, screwed it in, replaced rack, closed door, preheated oven, and then baked cookies! Great company, great customer service, and super fast shipping!