Models > AGS780WW > Instructions

AGS780WW (P1168601W) Amana Range - Instructions

Jump to:

All Instructions for the AGS780WW

Customer:: Chris from Piedmont, SC
Parts Used:: 32020101
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

This Amana gas stove is believed to have been manufactured in 1996 or thereabouts. The burners stopped self-igniting one at a time about 1.5 years ago. Since then we have lit the burners with a gas grill lighter.

Using a meter, we determined each of the four igniters had continuity from end to end and also had continuity from the end of each igniter back to the spark module. At that point we decided the module was probably bad and, after reviewing some similar-sounding problems on this website, I ordered the module. Installation was simple and solved the problem. All four burners now ignite as they should. One caution - the installation instructions that came with the new module did not describe anything like my stove.

Was this instruction helpful to you?

Customer:: Thomas from Dayton, OH
Parts Used:: 814323
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Burner grate pads worn off or missing

I took a jewelers screwdriver and completely cleaned out what was left of the old pads. Then applied a small amount of heat resistant rtv sealant to each hole, slid in the new pads and wiped off the excess. I let everything set overnight. The next day everything was solid. Job was complete. Note I've done this before and did not get the results I did this time. I believe it was the instruction that came with the pads and the tip-off to use the rtv. Thank you PartSelect T.Garr

Was this instruction helpful to you?

Customer:: Mary from Weston, CO
Parts Used:: 786324
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins

Broiler & burners worked, oven would not ignite or heat up.

Roommate did the repair..so I don't know. I did the research online, the igniter solved the problem. Saved us buying a new oven!

Was this instruction helpful to you?

Customer:: Peter from Eagan, MN
Parts Used:: 32020101
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

2 burners not igniting

Removed the burners 2 screws per burner disconnected the wires to the burners. Lifted the oven top off removed original ignition module. Installed wires to the new module taking note of replacement location. Than mounted new ignition module. Tha only hiccup was dropping 1 screw down into the stove lining found replacement screw and installed module. Cleaned and replaced top. Mounted burners and the stove is working like new. Project proved to be quite simple and guick. Thanks to partselect for there prompt delivery and other peoples input on install made it quite easy and simple,

Was this instruction helpful to you?

Customer:: Patricia from Milwaukee, WI
Parts Used:: 786324
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

stove sometimes would not light or took really long and did not maintain heat

We unplugged the stove and turned off the gas. We slid the oven door off just to make it easier. Unscrewed 3 screws holding the igniter in place. Pulled the igniter out from the back of the stove. Disconnected the two wires. Slid the new igniter in the holder. Rewired it and slid it back into place. Put the screws back in and it was done. Plugged it back in, turned the gas on, tried it out and presto! It was perfect! Lit immediately and strong and now i have a brand new 20 year old stove. lol Happy girl! And this was done by 2 50 year old women!

Was this instruction helpful to you?

Customer:: Wesley from Norman, OK
Parts Used:: WPY0314907
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

Oven not heating, F3 trouble code.

Removed back panel, unplugged sensor, removed sensor from inside oven (2 screws), replaced with new part.

Was this instruction helpful to you?

All Instructions for the AGS780WW