ARG7301LL-P1143328NLL Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary Jane from Union City, TN
- Parts Used:
- WP314763J
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
just moved.range oven had only 1 wire oven rack
I just ordered a new wire oven rack from you. When it came all I had to do was to remove it from the carton it came in and place it in the oven. It fit perfectly. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Eau Claire, WI
- Parts Used:
- 786324
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven gas valve would not open
Removed oven door. Removed three screws on ignitor holding bracket. Pulled out the range from the wall and reached underneath to access the wire nuts on the wires. Removed old ignitor and replaced with new one. Reconnected wires and then and replaced bracket and that's it. Works great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from hillsboro, OR
- Parts Used:
- WPY0316773
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
none of the burners would light
I removed all 4 burners 2 screws holding each,replaced the ignition module,wire for wire,reassembled after cleaning the stovetop.I,m my wife's hero.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Chicago, IL
- Parts Used:
- WP31940001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven either would not come to set temperature or took a very long time. Gas would flow to burner for only short times. When burner was lit, flame was often low. There was often the smell of gas.
Symptoms were sign of bad ignitor based on Goggle searches. Removed screws holding burner and ignitor to range. Disconnected ignitor at green connector below oven with lower drawer removed. Then removed burner and old ignitor. Reinstalled burner and then new ignitor being sure burner was still seated on gas outlet. (Note-burner removal may not be necessary) Replaced two screws attaching ignitor to oven wall and two screws attaching burner to floor of oven. Oven works perfectly now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from Milwaukee, WI
- Parts Used:
- 786324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The oven would not light up.
My husband took the oven door off then the bottom piece below the shelf took the old ignigter out put the new on in and now I have an oven again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stanley from St. Louis, MO
- Parts Used:
- WPY0316773
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
The spark was no longer igniting the burner
The earlier reviews said very easy and 15 minutes for beginners. They were right on, except I could not get the old screw out no matter what I tried. I eventually had to drill it out and put in a self tapping new screw. This was a first for me. Then it took 15 minutes or less and works fine again. Hopefully next time someone will tell me how to get that old screw out faster.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gregory from sayreville, NJ
- Parts Used:
- 786324
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
oven would not light/get hot.
I slid out the oven burner disconected the old igniter and replaced it with the new one & slid back in place and connected the two wires and I was back in business. The job was relativly an easy one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from CONCORD, CA
- Parts Used:
- WPY0316773
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rear burner of sealed cartridge did not light
I removed the cartridge from the range and used a screw driver to remove the screws holding the burners assembly in the housing. (Some prefer to remove the burner from the top by removing the two screws, but I've had trouble realigning the parts that way.) I removed the ignition wire and the screw holding the bad electrode in the burner. I then installed the new electrode, attached the ignition wire, put the burners assembly back into the housing, and put the housing back into the range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sonora, CA
- Parts Used:
- WP7504P109-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner would not ignite even with gas flow spark and clicking.
Removed two screws and disconnected the ignition wire. Then connected ignition wire to new burner and installed two screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Philadelphia, PA
- Parts Used:
- WPY0316773
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
cracked ignitors (2)
No problem removing the burners. Removing the old initors was a different story. The tiny screws that hold the ignitor in place were baked in and could not be removed with a screw driver. I drilled them and tried to use an easy out to no avail. The screws are very short so I had to use care not to drill thru the burner. Both screw heads did snap off. I resorted to a hi temp epoxy to secure the ignitor flanges to the burner and now the all burners ignite as designed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from lancaster, NY
- Parts Used:
- WP31940001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Oven would not light, broiler would
Remove the cover over the burner, two screws at the rear, this exposes the burner tube cover, one nut at the center. Three screws will remove the holder for the igniter. I had to remove a sheet metal cover underneath the oven( pull the drawer out) to gain access to the plug for the igniter. A good tip on this is the same valve controls the broiler and the oven, if one works and the other doesn't, it's the igniter. If neither works the gas vale may be the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Bethel, CT
- Parts Used:
- WP31940001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven igniter would not ignite
1. Removed drawer
2.Removed back panel (2 screws).
3. Disconnected power line from old igniter
4. Removed 3 screws holding old igniter.
5. Replaced with new igniter.
Works like new.
2.Removed back panel (2 screws).
3. Disconnected power line from old igniter
4. Removed 3 screws holding old igniter.
5. Replaced with new igniter.
Works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Kingman, AZ
- Parts Used:
- WP31940001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven & Broiler wouldn't light
I replaced the Oven Igniter. With a ohmn meter I checked the resistance on the Igniter and there was nothing there. I figured the module had to see some kind of resistance to turn the gas on. The Oven now works after replacing the Oven Igniter, but the Broiler still will not light. I will check the resistance on the Broiler Igniter and see what is going on there.
The Igniter can be checked from the back by removing the back cover panels. The two igniter wires come out through the back of the oven and have heat resistant covering on them. They run into a plastic plug and can be accessed at this point to check the resistance.
To remove the Oven Igniter, remove the oven racks, the bottom panels which are held on by screws. The Oven Igniter is attached to the gas rail which is attached to the underside of 2nd panel by two wing nuts.
The Igniter can be checked from the back by removing the back cover panels. The two igniter wires come out through the back of the oven and have heat resistant covering on them. They run into a plastic plug and can be accessed at this point to check the resistance.
To remove the Oven Igniter, remove the oven racks, the bottom panels which are held on by screws. The Oven Igniter is attached to the gas rail which is attached to the underside of 2nd panel by two wing nuts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Lake Zurich, IL
- Parts Used:
- 786324
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Broiler Would Not Turn On
Un plug elect. Cord. Remove door by pulling upward removed back stove panel, un did 2 wire nuts leading to igniter. Un screw igniter inside oven at top next to burner pad. Interchanged old ignitor with new plug stove back in. Thats it.
Was this instruction helpful to you?
Thank you for voting!