ALY1680BDB Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ruben from El Paso, TX
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Burners were not working properly. They had rusted out.
First I turned the burner head counter clockwise, lifted it out and pulled the connectors off. Then I connected the connectors back on the prongs of the new burner head and placed it back on the gas line and turned the burner head clockwise. I then turned the pilot light and and tested the connection. It worked without any problems. I then proceed to replace the second burner head using the same steps as on the first burner head.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Evanston, IL
- Parts Used:
- 3608W056-70, 3608W055-70
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken trim parts on my RV stove
Removed the stove from the RV, unscrewed the old trim parts and installed the new ones, slid the stove back into it's slot in the RV. Piece of cake
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Casa Grande, AZ
- Parts Used:
- 74003929
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven door handle broke in two pieces
Remove two black Phillips head screws from the top of the oven door and two black Phillips head screws from the bottom of the oven door which releases the door from the oven. Remove the two Phillips head screws that hold the handle and discard broken handle. Install new handle onto door and then replace the door. Easy!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Shelley, ID
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broke the insulator on the ignitor while cleaning the cooktop.
Unscrew the bottom cover, remove the old ignitor. Reverse the process to install. Hardest part was getting the bottom cover screws out because of rust. Otherwise, very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robin from saint marys, GA
- Parts Used:
- 74004053
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
2 burners rusted apart, 1 gas valve frozen up.
Removed burner pan screws,igniters, gas tubes & burners. Changed 2 igniters, removed rust & repainted ends of 2 of the tubes (heatproof paint). New burners were made a hair smaller than original but locked in O.K...Now, the hard part...disconnected all four tubes from gas valve assembly. (Had to shut off gas to house in order to remove main gas line to stovetop.) Had to remove valve box in order to remove/replace frozen valve. Unit is 25 years old, works as and looks new...Rust was caused by boil-overs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Richwood, OH
- Parts Used:
- Y8007P02060
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
original grommets broken
The new grommets were NOT the correct parts, too big, so there was no repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from South Burlington, VT
- Parts Used:
- 74004053
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burner igniter was not lighting the pilot. Needed replacement.
We replaced 3 of 4 igniters on the stove top according to the previously submitted recommendations. Easy to do butt after putting one of the modules back together, we found one igniter still didn't function. We discovered the solution was to run the connecting wire under the gas tubing. Apparently it was compressed when it was over the top of the tube and not under it.
Was this instruction helpful to you?
Thank you for voting!