ACS4660AB-PACS4660AB1 Amana Range - Instructions

plugged it in screwed it in placed grease filter in place DONE 3 minutes tops piece of cake!!

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

Took out two screws, threw the old one away, and put the two screws back in. Then washed up.

Very simple process of just ensuring you have the correct size racks and remove the old racks and replace them with the new ones.
Having ordered a lot of things on the internet, I am very pleased with using Part select and would "highly" recommend them to all!!

The repair was quite easy. Remove the two screws and put in the new part. The only problem I had was the hinge sent was the wrong side (but it still worked) and the new hinge had no threads for the screws. I had to tap the holes so that the screws could be used.

After I received the new hinge in the mail, my 13 year old son volunteered, for a fee of five dollars, to put the new hinge on the oven door. Seeing "easy to install" on the outer wrapper of the new part, I thought I was being generous. However, my son soon let me know that the screws given with the new hinge did not fit into the predrilled holes of the oven. He tried and tried for over an hour to get those screws to fit. I decided to go to the home improvement store to buy bigger screws. I took the hinge with me and had the store employee assess the type of screws I would need. He then informed me that the screws were fine, but I needed the holes in the hinge to be drilled bigger. I bribed him by offering to buy him a drink if he'd do it for me as long as he was single. He laughed and drilled away. (Sometimes, single women, like me, get desperate!) He handed me the hinge with larger holes and I noticed the wedding ring. Oops...no drink for him!! But I did give him a great big thank you. Happily, I brought the fixed piece home and handed it to my son to continue with the repair. He tried again and this time announced the holes were drilled too big!! If there was a bridge nearby I seriously would have jumped! The next day I drove to my Dad's house...a true jack of all trades...and with his drill and two new screws, he said this should do it. For the third time, I handed the hinge to my son and VOILA!! It actually worked! Thanks Dad!! So much for "easy to install". Seriously, the incorrect screws were sent with this hinge! Anyway, I happily celebrated that night with a drink in my hand...minus the home improvement employee!

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Really easy!! Cut off Breaker so the Range had no power. Use phillips head screwdriver, remove the two screws holding the bake element in. Remove connectors from element. I put (heat shrink) wrap around the female connectors then attached them to the element, heated the shrink wrap, replaced the screws and cut on the breaker / power. Turned on the oven (350) to "bake" off the oil film off of the element. (Element will smoke / smell for a few minutes).

I went online to learn what F-3 meant and it said temp sensor malfunction. I ordered the part - it looked the same so I repaced the old one and then the plugs were different. I cut the plug off the old sensor and cobbled together a connection. I powered up the stove and the burners were ok, but the oven appeared dead. about an hour later the alarm went off and it displayed F-1. I figured I needed to order another part, but hit Oven cancel and the display lighted up. I set the clock, heated to 400 and made a tray of cornbread. It seems to work ok, but I need to make a better arrangement. perhaps cut the new part connector off and splice the old connector. I don't like having electrical tape so close to the oven - it will probably melt with much usage. It is working - for now!

Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old hinges and installing the new ones.

very easy

Screwed in light bulb and glass protector

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.