ARGS7650E-P1130755NE Amana Range - Instructions

Replacing the igniter itself was a simple matter a few screws holding its housing and then plugging the new one into the connector. Difficulty came trying to figure out how to access the igniter. Disassembling the floor of the oven was a dead end involving many screws. Pulling the unit out from the wall was a big job and another failure. The problem was solved with the removal of the drawer. Underneath, in the rear was a sheet metal plate held by 2 screws. Behind that hung the igniter connection. Voila! Job done.

Replaced the existing ignitor by removing the bottom drip pan/gas line/ignitor (apprimately 18 screws), unscrewing the wire nuts, removing the old ignitor, connecting the wires to the new ignitor, and reinstalling the drip pan/gas line/ignitor (18 screws).

Wow, ordered the part here and it arrived in 18 hours!! Job was fairly straight forward but the screw holding it in place was corroded and stuck. Several heating and cooling cycles with a torch and some spray lube and lots of patience and I finally rocked the screw lose.

Took bottom oven pan off accessed through oven storage drawer.Removed a few screws holding the igniter bracket,removed igniter from its holder(Be really,really careful doing this procedure because the igniter tip is verrrrry fragile,ask me how I know)Put it all back together and Voila,it works!This is so easy a job a caveman can do it! Good luck!

Unscrewed all the phillips screws holding the door together. Re-assembly indicates that you want to note exactly how the sides overlap the front and back steel panels, possibly take a cellphone picture before starting. The front and back panel will bend down the bottom attachment metal tabs, misaligning the sides, etc if you replace the glass with the door still on the range. Prob. best to have a second standing by or remove entire door first.

Easily replaced the stovetop burner bowls by removing the old ones and replacing with the new ones.

Parts Select provided easy online ordering and was nearly one-half the price of other online suppliers.The quality was excellent!

Put the new pad in and it was done. Very easy.

Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You

For the third time in less than a year I had to replace the broiler igniter. The range is 27 years old and has given us excellent service. When the igniter failed it's replacement lasted 3 months. The next replacement lasted about 6 months. This last replacement has been in service about 1 week. We shall see. The last one had an open wire within the ceramic mould. There was continuity from one wire, through the black portion, but not to the second wire. It seems like it was a fault in manufacturing.

Daughter and family came to visit Gramps for the weekend; Saturday morning, arose and opened a couple of cans of grand buscuits. Set aside to let rise then turned oven on to preheat. Came back later and oven did not work. Stove top worked, broiler worked, but no oven. What to do, didn't want to waste dough; perhaps salvage for dumplings, no; make poorboy doughnuts, no; Aha, lets use the outside gas grill, never done it, worth the try, remember old camping days except using gas. Worked like a charm, crisis over. Now back to oven. Since everything worked except the oven burner problem could be in the igniter, or oven control. Removed covers to burner assembly, pulled igniter, checked for continuity across the two leads. No go. Wait, need to check oven control, placed voltmeter across incomming leads, turned oven controls on and had voltage. Conclusion, igniter bad. Also noticed a small rust hole in the burner tube next to igniter, not good. Went on-line to PartsSelect, entered make and model number. No model but gave choice close to model. Viewed pictures, found one that came close. Placed order. Parts came in a very short time. Matched new parts to old. perfect. Removed burner tube and installed new one, one screw, simple. Wire nut the incomming leads to igniter and install, three screws, simple. Turned oven on, igniter glows bright, gas comes on, good blue flame, no need to adjust air inlet vents on burner tube. Turned off oven, replaced covers, then turned on oven, baked cornbread and enjoyed. Thanks, back in business. Dave

The repair was fairly simple. The hardest part was figuring out the best way to get access to the part. Basically just had to remove the cover at the bottom of the oven then remove the shield that was directing the heat that comes off of the burner. Once I had access to that, I could see the ignitor. To get access to the plug in section, I had to take out the bottom drawer for pots and pans, then remove the piece above that to get access to the place that the ignitor plugs into. Unfortunately the wires were too short, but so were the ones that were on the current ignitor so I used the extension from the existing ignitor and cut off the plug of the new one to attach the extension. Once that was done, just reinstalled the ignitor and we reversed the process. The new one works incredibly well. Instead of waiting several minutes for the oven to start heating up, it heats up instantly. What a relief...much cheaper than buying a brand new stove. This one works great now!! Thank you parts select!!

I removed the oven door by removing two screws, one above each hinge. With the door screws removed, position the door to the slightly open position and lift strength up to remove. Remove wire racks and the cover from the bottom of the oven. Remove the heat deflector which is held on with a single nut. Remove the screws that hold the cavity that houses the igniter and the burner. The igniter is held in place by a protective bracket that has to be reused. I slid the old igniter out of the protective bracket and then removed the cavity by allowing the burner and igniter to exit through an opening in the rear of the cavity. The drawer (broiler pan storage) had to be removed to remove the two screws to an access panel that allowed access to the igniter connector. After disconnecting the old igniter, I fished the new igniter connector through the back of the oven to connect it. I use masking tape to hold the access panel in place while reinserting and tightening the two screws. Replace the cavity that houses the igniter and burner. Slide the protective cover over the igniter. Realign and secure the burn and igniter assembly by reinserting and tightening the necessary screws. Reinserting and tighten the screws around the igniter/burner cavity. Replace the heat deflector by tightening the nut. Replace the cover that covers the bottom of the oven and the wire racks. Reinsert the drawer. Slide the door over the hinges and reinsert and tighten the two screws.

I have an older model gas oven which required that all screws had to be removed. With a screw gun the job would not haven taken long. Once the bottom pan was removed the oven ignitor took some finese to remove. This was only due to the short wires. Once pulled sufficiently to be able to disconnect the ignitior (although I was afraid I was going to pull the wires and separate them from the stove), it was very simple to unplug and plug in the new one (again, making sure to hold the plug so the wires would not retract back behind the wall which would have required the stove to be pulled out from the wall and the back disassembled).

The good news, it was a success and the oven works like new. Roughly $38.00 later, I am back cooking. The extra effort for the screws was offset by being able to complete this by myself and saving the cost of a repair man. Would do it again.

First I had to take the drawer completely out of the stove to reach the igniter. I then removed the screws that held the igniter in place and removed it. I had to slightly modify the replacement part by squeezing it together to make it fit into the same space. I put the replacement igniter in place and screwed it down; put the drawer back in the stove and turned on the over to see if it would light. Bingo, job done!

Removed screws on edges of door. Romove front panel. Remove several screws around glass. Replace inner glass and replace screws. A little tricky reinstalling trim around door front.