ARS635P1113801S Amana Range - Instructions

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

I ordered the new part, which arrived in just 2 days. I did not pull the oven away from the wall, I merely turned off the electric, unscrewed the bad element, pulled it out enough to see the ends, and then I removed the existing wires using needle nose pliers. I put the wires on the new element, inserted it back into the oven wall, and screwed it tight. I turned the electric back on, and checked it out. Worked like a charm! Only 40 bucks (including shipping), five minutes of my time, and I avoided an expensive service call. :-)

Turned off 230 volt breaker to range,connected old wires to new element ,put back into place replaced the two mounting screws. Turned breaker back on and tested range.

Pretty simple. Turned off breaker. Lifted the top, cut the 2 wires. Going to the burner, put the 2 wire nuts on, and screwed the bracket in.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected the new wires, replaced the two screws and turned on the oven to test it. Easiest repair job I have ever done.

Removed old block , cut off wires , used new wire nuts, heat shrink , supplied with parts , job done lowered range top went fishing ...

Removed 2 phillips screws and pulled elements out 3 to 4 inches. One of the leads touched the housing and blew the circuit breaker, so don't forget to unplug or turn the breaker off! Simply slide clips off and install on new element. push back in place and reinstall 2 screws. Very simple.
P.S. element was delivered very fast!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.

Two screws in the oven removed the old part and the wires unplugged from the unit. When the new part came in , it was plug and play. Plugged the wires into the new part, put part into holes in oven and screwed the screws back in place and we were ready to go. The part was here in record time. We ordered it on Sunday, it shipped out on Monday, it arrived on Tuesday and we were back in operation! Thanks for a really smooth repair experience!

Al lI had to do remove the oh swith & attach th e new on & push in place
It took about 5 min. to turn off the electric & to turn it back on.
Glen V

Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so you have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.

I just installed the new burners into the proper place and they fit This was very easy to order. Just had to find the model number which the web site told me where to find this. I am very satisfied with the service Thank You

Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be sure and disconnect power before starting!!

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

r & r hinge. very poor pivot pin which leads to frequent replacement of hinge assembly, cheaply made, weak spot is hinge pin pivot rivet.