ARGS7650E-P1130762NE Amana Range - Instructions

Ceramic connectors were taken off the old igniter, pulled off old igniter and replaced in the same way the new igniter

Removed old ignightor and installed new one

Installed new igniter - easy job. Remove burner deflector, remove screws holding igniter bracket, remove panels below oven (accessible via removal of drawer), disconnect igniter and remove. Remove igniter from bracket, slide new one into bracket and reverse the steps to install it. Unfortunately, it didn't work. Igniter not glowing. I checked continuity on the igniter and it showed 90ohms resistance, so seems to be OK. Put multimeter on range plug end, turned on oven and multimeter did show cycling voltage at the plug (although I'm not certain what it should read). Relay in the control board does 'click' when oven turned on, so it also seems to work. Think I may be down to the gas control safety valve for the oven, but it is no longer available. Anyone have any other ideas? Hate to buy another igniter and have it still not work. Thanks!!

Followed Instructions with part. Easy Install. However the problem not solved. I believe Oven Control defective (Worn Out). Replacement May not be available. Still looking. Thank You. RJC

I bought the part and replaced it.

I ordered the part and it was at my door in 2 days. I ordered the part on Wednesday thinking I would install it on the weekend after next. The part showed up on Friday. That was amazing considering I didn't sellect expeidited delivery. I didn't have a manual and have never tried this before so grade my attempt on a curve please. I started by unscrewing the screws closest to the hinge but quickly migrated to the entire face of the range. Pulled the range out and started unscrewing the screws on the side, and then the back. Figuring nothing was coming off and I still couldn't get to the hinge I stopped and regrouped. That's when my wife asked if she could help. I guess I looked distressed. By this time I had removed the drawer and had the range on it's back in the middle of the kitchen with little bowls of screws everywhere. My wife picked up the new hinge and looked it over. Then she started playing with the old hinge which was loose, but I couldn't get it out. She realized that you can remove the old hinge and install the new hinge without taking the whole thing apart. Where was she 30 minutes ago? The hinges came out and the new ones went it in about 10 minutes. It took me another 20 minutes to put back all of the screws I had taken off unnecessarily. Sometimes use your brains instead of a screwdriver. I have the best wife ever!

I ordered new racks to see if they weere out of alignment. The new racks fell from its tracks after the broiler was heated. It seems the oven cabinet is expanding with the heat and the rack width does not compensate for that. The new racks did not solve the problem so I do not know what can be done next. Any shelf support would have to be heat resistent. Replacing the oven cabinet is not a good option and no gauantee it wouldn't continue with this stove.

I removed the ignitor.
Ordered the matching part.
4 days later the part arrived and I installed the part.

We removed the oven protective shield, took out the broken glass (very carefully) and replaced it with the part shipped. Then, we replaced the protective shield and it was done.

Removed the oven racks for room to work.
Removed a protective cover (slide forward, lift up).
Remove winged cover plate.
See igniter assembly.
Remove 2 or 3 holding screws (I don't want to go in and count them - it's obvious - they are clearly in view - get a good screw-driver seating - they come out easily).
The igniter assembly is then loose and ready to com out.
Remove the stove drawer to get at the access plate at the rear - comes off easily(the wires to the igniter were then clearly identifiable).
Release the wire plug - I marked one side with a sharpy - polarity of fit, not voltage.
Gently feed the igniter assembly out the bottom using the wires.
Remove the igniter from the shroud (may have to pul it apart a little - it's tight - it does come out easily after prying the shroud a little - mark a side with a sharpy - for mechanical orientation.
The part number should be on the igniter.
I did not bother matching the part number.
Just matched the stove brand and model.
The parts diagram provided by PartSelect was invaluable.
I put an ac meter up the holes of the plug (stove side, of course) turned on the stove to see the meter measure 115vac - assurance that the igniter was bad and not anything else.
Just reverse the removal process.
Just takes a little time and patience.
Very very doable.
Good luck.

shut off gas at tank, pulled stove out from counter area to gain acess to back, removed oven door removed removed screws holding igniter unit in place, i then removed the stove rear panel to get at the wiring for ignitor,remoded old part returned to front and installed new part, checked voltage then re-connected new wires, turded gas back on and tested oven, oven came on less than a minute, put rear panel on stove put door back on and put stove back into counter area, stove works like new.

Replaced glow bar/ igniter.

I pulled the ckt breaker, removed the oven drawer and disconnected the igniter. I opened the oven door and unscrewed the igniter holding bracket and removed the bracket and igniter. I broke the old igniter element when removing it from the bracket. When installing the new igniter in the holding bracket I broke the ceramic element. REALLY BE CAREFUL. Ordered a new igniter, very carefully installed it in the bracket, then rversed the removal process. It's not hard, you just have to be careful

First, I removed the oven door (two screws and pulled it off the hinges) and placed it out of the way. Then I removed the baking racks and bottom cover over the heating element this exposed the heating element, easily removed (two screws). I unplugged the old element, plugged the new element in, and put all the stuff back and the put the door back on. Next was the fun part. . . Had to get the wife to turn on the oven (very complicated touch pad - not made for a man to understand), and shazamm the oven came on! Now I can have some of those great homemade biscuits again!

1. Removed racks
2. Removed bottom cover
3. Removed screws holding ignitor
4. Removed storage draw
5. Removed cover over wires
6. Unplugged ignitor & placed with new
7. Put back together