ARG7301L (P1143328N L) Amana Range - Instructions

I ordered new racks to see if they weere out of alignment. The new racks fell from its tracks after the broiler was heated. It seems the oven cabinet is expanding with the heat and the rack width does not compensate for that. The new racks did not solve the problem so I do not know what can be done next. Any shelf support would have to be heat resistent. Replacing the oven cabinet is not a good option and no gauantee it wouldn't continue with this stove.

After I received the new hinge in the mail, my 13 year old son volunteered, for a fee of five dollars, to put the new hinge on the oven door. Seeing "easy to install" on the outer wrapper of the new part, I thought I was being generous. However, my son soon let me know that the screws given with the new hinge did not fit into the predrilled holes of the oven. He tried and tried for over an hour to get those screws to fit. I decided to go to the home improvement store to buy bigger screws. I took the hinge with me and had the store employee assess the type of screws I would need. He then informed me that the screws were fine, but I needed the holes in the hinge to be drilled bigger. I bribed him by offering to buy him a drink if he'd do it for me as long as he was single. He laughed and drilled away. (Sometimes, single women, like me, get desperate!) He handed me the hinge with larger holes and I noticed the wedding ring. Oops...no drink for him!! But I did give him a great big thank you. Happily, I brought the fixed piece home and handed it to my son to continue with the repair. He tried again and this time announced the holes were drilled too big!! If there was a bridge nearby I seriously would have jumped! The next day I drove to my Dad's house...a true jack of all trades...and with his drill and two new screws, he said this should do it. For the third time, I handed the hinge to my son and VOILA!! It actually worked! Thanks Dad!! So much for "easy to install". Seriously, the incorrect screws were sent with this hinge! Anyway, I happily celebrated that night with a drink in my hand...minus the home improvement employee!

Took the pan out of the bottom of the oven. Took the screws out of the assembly for the iron, disconnect the power wires under the stove and pull out the old iron. Reverse the proceedure but be careful with the new iron, it is very fragile. Connect the wires put the screws back and you are done. Make sure before you start the job that you unplug the appliance !!!!

The repair was quite easy. Remove the two screws and put in the new part. The only problem I had was the hinge sent was the wrong side (but it still worked) and the new hinge had no threads for the screws. I had to tap the holes so that the screws could be used.

It was really easy because I read information on your site. I only had to unscrew 3 screws, remove the old spark ignition electrode, replace the new one and then screw the 3 screws back. It was great

1. Remove sliding shelves and lower pan sheild
2. Remove flame deflector
3 . Remove the 3 screws that hold the igniter in place. Insert the new cable and plug through the opening for connection in step 6. You may hve access to connector. If so skip to step 8.
4. Remove sliding storage drawer
5. Remove the sheetmetal pan to gain access to the igniter connector. It might help to have several blocks of wood the elevate the frront of the stove to allow more working clearance.
6. Disconnect old igniter, connect new igniter.
7. Replace pan and sliding drawer.
8. Remove old igniter from carrier and install new one.
9. Install igniter carrier to stove with 3 screws
10. Replace flame deflector and lower pan sheild.

First I removed the two screws that hold the element in plance. I then pulled the element out about 3 in ches and disconnected the two wires

The repair actually started online trying to figure out the problem. The parts list and picture provided were a big help. I actually got lucky when I ordered the part. It was a little difficult to get to but once I got the old one out, it was easy and done quick. Saving at least $100 on a repair man was awesome. I had to find the part in the stove first. Then had to find the wiring harness to disconnect. After taking off the back panel and the oven burner plate, the wire harness was exposed. I disconnected, taped on the new wires, remounted the new igniter and put it all back together. Pretty quick and pretty easy.

1. Disconnect oven electric supply.
2. Remove oven door (2 screws).
3. Remove inside-oven bottom plate (slide forward, lift).
4. Remove inside-oven burner cover (1 nut).
5. Disconnect igniter enclosure (3 screws).
6. Remove under-oven drawer (slides out).
7. Remove panel at back of oven in under-oven compartment to access igniter electrical connection (2 screws).
8. Disconnect old igniter.
9. Extract old igniter from igniter enclosure. (Don't use much force; just slightly expand the metal flanges of the enclosure.)
10. Dispose of old (bad) igniter.
11. Insert new igniter into igniter enclosure.
12. Place igniter enclosure in oven compartment and slide electrical connector through to back/lower compartment.
13. Connect new igniter in under-oven compartment.
14. Replace panel at back of oven in under-oven compartment (2 screws).
15. Replace igniter enclosure (3 screws).
16. Replace inside-oven burner cover (1 nut).
17. Replace inside-oven lower plate.
18. Replace oven door (1 screws).
19. Reconnect electric supply.

this was the second one replaced in 5years,they don't make things like they used to

Took cover off inside of oven to expose igniter - 1 nut! - igniter would not glow --3 screws to remove - pulled out storage drawer - un screwed oven shields - (2) - 6 screws - unplugged plastic igniter plug - an replaced! - simple - thank you and made wife buy me dinner for the probably $60 service call! --- thanks to those that posted before me to make this possible!

Identifing what part to replace was the most challenging task. So, what I did to trouble shoot what was broken and identify the specific compent was the following. I was not sure that the igniter was broken becuase it illuminated rather bright but the oven would not turn on. The broiler on the other hand worked fine so I removed the igniter from the broiler and placed it in place (the igneiter is a different size) of the oven igniter and guess what the burner cut on...So I ordered the oven igniter and everything worked fine.

Removed racks and pans from oven, removed 1 screw that housed the v shaped burner cover. Then I noticed the Igniter housing was held to back of oven with 3 small screws, removed 3 screws, and noticed the igniter just slid into the housing, but the connection would not come through back of unit. pulled out the lower tray to expose the underside of the oven and noticed 2 screws holding a metal cover, removed those and noticed connection to igniter, undid the connection, slid out the igniter and then just reversed the process to put back. It took me about 20 minutes, and that was only because I was being overly careful with the ceramic igniter, as the one in there just crumbled. Very easy job for anyone with even moderate skills. Ordered my part with assitance from a lady at parts express on Monday at noon, had the part delivered Tuesday at 3:00, had the oven back up and running fine by 3:30. Couldn't be happier, as this happened once before and the repairman charged me $185, this cost $48 and 15 minutes.
Unbelievable service and detailed help. I have this site bookmarked for anything moving forward.
Thanks

Turn off power to unit. Remove one nut inside bottom of oven to expose glow bar and igniter. Take 3 screws off of ignitor cover and remove it.

Pull out pan storage drawer to expose igniter plug connector. Unplug connector. Remove igniter.

Plug in new igniter and reverse the above instructions to reassemble.

This was a much easier repair than I thought it would be. I read online that, given the problems my oven was having, it was almost certainly the igniter that was the problem. It was - with the new igniter it works perfectly!

My husband took it apart then showed me how to put it back together. So I placed it in the metal holder and attatched all the screws.