ARG7800LL-P1143322NLL Amana Range - Instructions

looked at and saw that ignitor was cracked,saw simple repair ahead. just needed the right part . Without part , select simple ,and easy selection, i might not have ever found the right part. as i said before finding the right part is 90 percent of the job and they made that an easy task .

of course if you want me to describe in detail, took out the pan saw the bad ignitor, removed 2 serews, disconnected 2 wire, the reassembled in the opposite direction. 30 minutes tops. I am sure this saved me at least 150 bucks for some "so called reparman" to do the same job, Most people do not realise that they have more education than most of these "repairmen". The only advantage these "repair people" have is acess to schematics and part numbers. Part select is a good start on putting this information in the hands of us average "idiots" as I am sure the repair folks call us when we pay 200 bucks for a 30 dollar job.

WEB research indicated that even though ignitor would glow, that it was likely faulty.
Turned off power at circuit breaker
Remove shelves and bottom plate from inside oven.
Unscrew deflector plate
Remove drawer under stove
Remove ignitor and unplug from connector
replace ignitor, plug in, reassemble stove.
Needed flashlight to see under stove.

I had done this before, but a while back, so it took a little longer to disassemble and find the igniter. Once there, easy to troubleshoot with a meter. Reassembly was only a few minutes and part of that was finding a new nut, since I lost one. I had to remove the storage drawer, then remove a metal cover to get at the connections. I tested the power to the igniter and found it to be OK. I tested continuity and had some but very low. Pulled the diffuser and cover off burner to locate igniter. Ordered part,put it on and reassembled everything. Working fine.

Installed new igniter - easy job. Remove burner deflector, remove screws holding igniter bracket, remove panels below oven (accessible via removal of drawer), disconnect igniter and remove. Remove igniter from bracket, slide new one into bracket and reverse the steps to install it. Unfortunately, it didn't work. Igniter not glowing. I checked continuity on the igniter and it showed 90ohms resistance, so seems to be OK. Put multimeter on range plug end, turned on oven and multimeter did show cycling voltage at the plug (although I'm not certain what it should read). Relay in the control board does 'click' when oven turned on, so it also seems to work. Think I may be down to the gas control safety valve for the oven, but it is no longer available. Anyone have any other ideas? Hate to buy another igniter and have it still not work. Thanks!!

I removed the oven door by removing two screws, one above each hinge. With the door screws removed, position the door to the slightly open position and lift strength up to remove. Remove wire racks and the cover from the bottom of the oven. Remove the heat deflector which is held on with a single nut. Remove the screws that hold the cavity that houses the igniter and the burner. The igniter is held in place by a protective bracket that has to be reused. I slid the old igniter out of the protective bracket and then removed the cavity by allowing the burner and igniter to exit through an opening in the rear of the cavity. The drawer (broiler pan storage) had to be removed to remove the two screws to an access panel that allowed access to the igniter connector. After disconnecting the old igniter, I fished the new igniter connector through the back of the oven to connect it. I use masking tape to hold the access panel in place while reinserting and tightening the two screws. Replace the cavity that houses the igniter and burner. Slide the protective cover over the igniter. Realign and secure the burn and igniter assembly by reinserting and tightening the necessary screws. Reinserting and tighten the screws around the igniter/burner cavity. Replace the heat deflector by tightening the nut. Replace the cover that covers the bottom of the oven and the wire racks. Reinsert the drawer. Slide the door over the hinges and reinsert and tighten the two screws.

The repair was fairly simple. The hardest part was figuring out the best way to get access to the part. Basically just had to remove the cover at the bottom of the oven then remove the shield that was directing the heat that comes off of the burner. Once I had access to that, I could see the ignitor. To get access to the plug in section, I had to take out the bottom drawer for pots and pans, then remove the piece above that to get access to the place that the ignitor plugs into. Unfortunately the wires were too short, but so were the ones that were on the current ignitor so I used the extension from the existing ignitor and cut off the plug of the new one to attach the extension. Once that was done, just reinstalled the ignitor and we reversed the process. The new one works incredibly well. Instead of waiting several minutes for the oven to start heating up, it heats up instantly. What a relief...much cheaper than buying a brand new stove. This one works great now!! Thank you parts select!!

Removed burners and top cover to access ignition module.
Remove and replace module and reassemble stove.

1. Removed racks
2. Removed bottom cover
3. Removed screws holding ignitor
4. Removed storage draw
5. Removed cover over wires
6. Unplugged ignitor & placed with new
7. Put back together

Removed burner with attached igniter assembly by raising forward legs from slots and pulling unit from rear support. Note: this is contrary to instruction #1 on installation instructions. Then followed the remaining instuctions 2 - 7 as written. Everything worked as planned.

I ordered new racks to see if they weere out of alignment. The new racks fell from its tracks after the broiler was heated. It seems the oven cabinet is expanding with the heat and the rack width does not compensate for that. The new racks did not solve the problem so I do not know what can be done next. Any shelf support would have to be heat resistent. Replacing the oven cabinet is not a good option and no gauantee it wouldn't continue with this stove.

I bought the part and replaced it.

I ordered the part and it was at my door in 2 days. I ordered the part on Wednesday thinking I would install it on the weekend after next. The part showed up on Friday. That was amazing considering I didn't sellect expeidited delivery. I didn't have a manual and have never tried this before so grade my attempt on a curve please. I started by unscrewing the screws closest to the hinge but quickly migrated to the entire face of the range. Pulled the range out and started unscrewing the screws on the side, and then the back. Figuring nothing was coming off and I still couldn't get to the hinge I stopped and regrouped. That's when my wife asked if she could help. I guess I looked distressed. By this time I had removed the drawer and had the range on it's back in the middle of the kitchen with little bowls of screws everywhere. My wife picked up the new hinge and looked it over. Then she started playing with the old hinge which was loose, but I couldn't get it out. She realized that you can remove the old hinge and install the new hinge without taking the whole thing apart. Where was she 30 minutes ago? The hinges came out and the new ones went it in about 10 minutes. It took me another 20 minutes to put back all of the screws I had taken off unnecessarily. Sometimes use your brains instead of a screwdriver. I have the best wife ever!

Removed oven racks and bottom cover plate. Removed stainless steel diffuser to access igniter. Removed bottom storage drawer and unplugged connector for igniter. Removed defective igniter by by taking out 3 screws holding stainless steel mounting bracket in place. New replacement part had totally different bracket which prevented it from mounting in the proper orientation so I carefully removed defective igniter from original bracket and installed new igniter. New part was tacked in place by some sort of high temp adhesive that had to be carefully removed to allow it to be installed in old mounting bracket. Installed new assembly in the oven and when I tried plugging in the power connector I discovered the pins on the new igniter were the wrong sex; both sides had male pins! Removed igniter again and cut off the two pin connector and installed a brand new 2 pin molex type connector. I installed a mating connector on the original length of wire and connector that I cut from the defective igniter along with the heavy insulating material so I now had a properly mating set of connectors. Went through the mounting process again; successful mating this time. Oven lights in 50 seconds. If it dies again I'll have a connector of each
sex ready before repair.

The first one came damaged and customer service credited the first one and got another on the way the same day. They were awesome to deal with. I removed the oven racks, the burner cover, the storage drawr, and the door. That took about 5 minutes. I removed 3 screws that held the ignitor in place. I removed the 2 wire nuts from the wires in the drawr space. I slid the ingitor cover off the old ignitor and onto the new one. Slid the new ignitor into place and fed the wires below and put on the 2 wire nuts, then installed the 3 screws and tested the operation. I put the oven back together and put the tools away. Total time about 20 minutes.

found igniter not working, pulled up on door and it came off, lifted up bottom of oven and pulled out, removed wing nut on deflector to access igniter, removed igniter retaining bolts, unplugged connector, be careful not to let connector slip back in stove, and reverse process to install new igniter,, all took about twenty minutes, easy repair,