ARG7600W-P1143332NW Amana Range - Instructions

It was Tuesday before thanksgiving, panic as there was a big bird looking for a hot stove,
unplug stove from its electrical supply
turn off gas, not necessary but sometimes it's good to be safe.
inside oven remove bottom splash cover "pull towards you and lift out, then remove flame pan, one nut in the center, remove and lift out flame pan.
The oven ignitor was to the left of the burner, with 3 philips screws one attached to buner and the other two to the back of the stove, remove all three.
The ignitor is now loose,
remove bottom drawer and behind is a plate attched to the back of the stove with two screw, the screws are facing you as you look in where the drawer was, remove screws and plate to access the plug attatching the ignitor to its power supply .
go back to the oven and remove ignitor.
install new, feed plug through back, and put it all back together.
"ignitor very delicate, handle with care"
I am also not the biggest of guys and it can be awkward getting in the drawer space as you need both hands to plug it back in, so tilting the stove back, keeping safety in your thoughts at all times, would be a must for most people.

The repair was fairly simple. The hardest part was figuring out the best way to get access to the part. Basically just had to remove the cover at the bottom of the oven then remove the shield that was directing the heat that comes off of the burner. Once I had access to that, I could see the ignitor. To get access to the plug in section, I had to take out the bottom drawer for pots and pans, then remove the piece above that to get access to the place that the ignitor plugs into. Unfortunately the wires were too short, but so were the ones that were on the current ignitor so I used the extension from the existing ignitor and cut off the plug of the new one to attach the extension. Once that was done, just reinstalled the ignitor and we reversed the process. The new one works incredibly well. Instead of waiting several minutes for the oven to start heating up, it heats up instantly. What a relief...much cheaper than buying a brand new stove. This one works great now!! Thank you parts select!!

Remove the racks
remove one nut that holds the heat deflector
3 screws that hold the igniter
remove the drawer
remove 2 screws holding a heat shield in place.
unplug old igniter and reinstall

I used your instructions

First I had to take the drawer completely out of the stove to reach the igniter. I then removed the screws that held the igniter in place and removed it. I had to slightly modify the replacement part by squeezing it together to make it fit into the same space. I put the replacement igniter in place and screwed it down; put the drawer back in the stove and turned on the over to see if it would light. Bingo, job done!

Simple install - 6 -7 screws one nut. Once replaced oven worked good as new. Part shipped from PartSelect actually better than one installed by repairman 4 years ago - fit like an original part.

Thanks PartSelect.com

Disconect power source; Remove oven racks, remove storage drawer under oven; remove floor of oven, remove flame deflector, remove three screws holding igniter cage and unplug faulty igniter. Reverse all steps for reassembly.

Took the pan out of the bottom of the oven. Took the screws out of the assembly for the iron, disconnect the power wires under the stove and pull out the old iron. Reverse the proceedure but be careful with the new iron, it is very fragile. Connect the wires put the screws back and you are done. Make sure before you start the job that you unplug the appliance !!!!

Removed the three screws holding the igniter, pulled the old one out and plugged in the new one. Very simple.

diagram on website was very helpful. simply unscrew two screws,remove and replace electrode and works perfectly.
Ordered one day arrived next with standard shipping installed before next day supper awesome service

We removed the oven protective shield, took out the broken glass (very carefully) and replaced it with the part shipped. Then, we replaced the protective shield and it was done.

Unscrewed the old and screwed on the new.

shut off gas at tank, pulled stove out from counter area to gain acess to back, removed oven door removed removed screws holding igniter unit in place, i then removed the stove rear panel to get at the wiring for ignitor,remoded old part returned to front and installed new part, checked voltage then re-connected new wires, turded gas back on and tested oven, oven came on less than a minute, put rear panel on stove put door back on and put stove back into counter area, stove works like new.

First, I removed the oven door (two screws and pulled it off the hinges) and placed it out of the way. Then I removed the baking racks and bottom cover over the heating element this exposed the heating element, easily removed (two screws). I unplugged the old element, plugged the new element in, and put all the stuff back and the put the door back on. Next was the fun part. . . Had to get the wife to turn on the oven (very complicated touch pad - not made for a man to understand), and shazamm the oven came on! Now I can have some of those great homemade biscuits again!

Removed the oven racks for room to work.
Removed a protective cover (slide forward, lift up).
Remove winged cover plate.
See igniter assembly.
Remove 2 or 3 holding screws (I don't want to go in and count them - it's obvious - they are clearly in view - get a good screw-driver seating - they come out easily).
The igniter assembly is then loose and ready to com out.
Remove the stove drawer to get at the access plate at the rear - comes off easily(the wires to the igniter were then clearly identifiable).
Release the wire plug - I marked one side with a sharpy - polarity of fit, not voltage.
Gently feed the igniter assembly out the bottom using the wires.
Remove the igniter from the shroud (may have to pul it apart a little - it's tight - it does come out easily after prying the shroud a little - mark a side with a sharpy - for mechanical orientation.
The part number should be on the igniter.
I did not bother matching the part number.
Just matched the stove brand and model.
The parts diagram provided by PartSelect was invaluable.
I put an ac meter up the holes of the plug (stove side, of course) turned on the stove to see the meter measure 115vac - assurance that the igniter was bad and not anything else.
Just reverse the removal process.
Just takes a little time and patience.
Very very doable.
Good luck.