ARG7102W-P1143344NW Amana Range - Instructions

I used your instructions

Installed new igniter - easy job. Remove burner deflector, remove screws holding igniter bracket, remove panels below oven (accessible via removal of drawer), disconnect igniter and remove. Remove igniter from bracket, slide new one into bracket and reverse the steps to install it. Unfortunately, it didn't work. Igniter not glowing. I checked continuity on the igniter and it showed 90ohms resistance, so seems to be OK. Put multimeter on range plug end, turned on oven and multimeter did show cycling voltage at the plug (although I'm not certain what it should read). Relay in the control board does 'click' when oven turned on, so it also seems to work. Think I may be down to the gas control safety valve for the oven, but it is no longer available. Anyone have any other ideas? Hate to buy another igniter and have it still not work. Thanks!!

I have an older model gas oven which required that all screws had to be removed. With a screw gun the job would not haven taken long. Once the bottom pan was removed the oven ignitor took some finese to remove. This was only due to the short wires. Once pulled sufficiently to be able to disconnect the ignitior (although I was afraid I was going to pull the wires and separate them from the stove), it was very simple to unplug and plug in the new one (again, making sure to hold the plug so the wires would not retract back behind the wall which would have required the stove to be pulled out from the wall and the back disassembled).

The good news, it was a success and the oven works like new. Roughly $38.00 later, I am back cooking. The extra effort for the screws was offset by being able to complete this by myself and saving the cost of a repair man. Would do it again.

I just replaced the racks with beautiful, new, shiny racks. My wife was very pleased

1. Removed racks
2. Removed bottom cover
3. Removed screws holding ignitor
4. Removed storage draw
5. Removed cover over wires
6. Unplugged ignitor & placed with new
7. Put back together

Bought a new one. . Three years later =)

First turned off power to oven, Took burner out by lifting up and pulling out, then pulled out wires attached to the oven and igniter, removed two wire nuts and disconnected the wires then removed burner assembly from oven. With screwdriver and nut driver removed old igniter from housing and put new one in place, tightened up screws carried back to oven reattached wires with wirenuts and feed wires back into oven, then put burner back carefully silding igniter into hole in back of oven. Turned power back on to oven and worked nice. Took all of 15 mins to complete.

Replaced glow bar/ igniter.

First, I removed the oven door (two screws and pulled it off the hinges) and placed it out of the way. Then I removed the baking racks and bottom cover over the heating element this exposed the heating element, easily removed (two screws). I unplugged the old element, plugged the new element in, and put all the stuff back and the put the door back on. Next was the fun part. . . Had to get the wife to turn on the oven (very complicated touch pad - not made for a man to understand), and shazamm the oven came on! Now I can have some of those great homemade biscuits again!

Removed the oven racks for room to work.
Removed a protective cover (slide forward, lift up).
Remove winged cover plate.
See igniter assembly.
Remove 2 or 3 holding screws (I don't want to go in and count them - it's obvious - they are clearly in view - get a good screw-driver seating - they come out easily).
The igniter assembly is then loose and ready to com out.
Remove the stove drawer to get at the access plate at the rear - comes off easily(the wires to the igniter were then clearly identifiable).
Release the wire plug - I marked one side with a sharpy - polarity of fit, not voltage.
Gently feed the igniter assembly out the bottom using the wires.
Remove the igniter from the shroud (may have to pul it apart a little - it's tight - it does come out easily after prying the shroud a little - mark a side with a sharpy - for mechanical orientation.
The part number should be on the igniter.
I did not bother matching the part number.
Just matched the stove brand and model.
The parts diagram provided by PartSelect was invaluable.
I put an ac meter up the holes of the plug (stove side, of course) turned on the stove to see the meter measure 115vac - assurance that the igniter was bad and not anything else.
Just reverse the removal process.
Just takes a little time and patience.
Very very doable.
Good luck.

The first one came damaged and customer service credited the first one and got another on the way the same day. They were awesome to deal with. I removed the oven racks, the burner cover, the storage drawr, and the door. That took about 5 minutes. I removed 3 screws that held the ignitor in place. I removed the 2 wire nuts from the wires in the drawr space. I slid the ingitor cover off the old ignitor and onto the new one. Slid the new ignitor into place and fed the wires below and put on the 2 wire nuts, then installed the 3 screws and tested the operation. I put the oven back together and put the tools away. Total time about 20 minutes.

shut off gas at tank, pulled stove out from counter area to gain acess to back, removed oven door removed removed screws holding igniter unit in place, i then removed the stove rear panel to get at the wiring for ignitor,remoded old part returned to front and installed new part, checked voltage then re-connected new wires, turded gas back on and tested oven, oven came on less than a minute, put rear panel on stove put door back on and put stove back into counter area, stove works like new.

Researched through this site to find part numbers and names. Youtubed it to see how to install the part. Ordered the exact part via this site and received it in only a day or two. Installed it in less than 15 minutes and the oven works amazing. It gets up to temp quickly and holds temp better than it has in years. Very satisfied!

First I removed the three screws, then removed the old end cap, cleaned the area, and reinstalled the new end cap, then attached with the three screws.

Unscrewed the old and screwed on the new.