AGDS902WW-P1131828NWW Amana Range - Instructions

I first thought the burner was bad but after some
testing realized that the Spark Ignition Module was
faulty. You have to remove the screws from the four
burners to remove them and the stove top. Then it
is a fairly easy job to replace the module. Just be
careful to reconnect the wires in the correct places
that you removed them from the old module.

Subject range is in a rental house and receives much use and abuse. The repair was necessary due to the door having 2, 1-2 inch cracks one on each side so the door bent outward. Obviously in the past when the oven door was completely in the open position much weight was placed on the door cracking the sides and bending the door. Consequently, when the oven was in use and the door was closed being that the door was bent outward heat escaped from the top of the door heating up the control panel. The control panel would get so hot that it could not be touched without burning the fingers. Replacing this range would cost approximately $2200, so we had to try to repair it. I went to the ParSelect website and ordered the part I needed.
Being that the oven door is heavy and large it took two people to disassemble and reassemble the door. We had quite
a wrestling match with the door (consider too, that we never do this type of job) but after about 3 hours our range was almost like new.
Disappointing that a replacement mylar cover for the control panel is no longer available at PartSelect. We would appreciate getting our hands on one as the existing mylar cover is cracked.
The oven has been successfully used since the repair and we have a good fit and the control panel is now only warm instead of blistering hot. FANTASTIC!
THANK YOU


Time will tell.

Sincerely

Craig and Judy Crouch

I removed all 4 burners 2 screws holding each,replaced the ignition module,wire for wire,reassembled after cleaning the stovetop.I,m my wife's hero.

First I removed the two screw on the lower inside of the door that hold the door to the hinges. Then I opened the oven door at about a 15 degree angle, and carefully lifted the door out of the hinge brackets. Next I had to remove the side panels on the door . After getting those side pieces off, I realized that I had to go through all layers of the door to get to the inner glass, so I decided that the best way to keep track of all those screws, was to remove each screw with the Phillips head screw driver, and immediately scotch tape that screw right next to the hole it came from. That was the best idea I had, because there are many screws in that door! Removing the old glass, and replacing it with the new glass was the easiest part of the project, just be sure not to let pieces of the insulation get between the glass and the metal frame. Then I reversed my steps to put everything back together. It probably took a bit longer than someone else because I first taped each screw on the panels, and then had to remove the tape, but I just did not want to find a handful of screws after the door was back on, or worse, somehow lose one or two. I think the hardest part of this project was getting the door back on the hinges, because the door is heavy, and you have to line up the hinges with holes in door, and slide the door in evenly. Once the door is back on, re-insert the two screws, and your oven door is as good as new (and as clean as new).

Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.

Philips is all that's needed. Remove the burners (2 screws each) lift off top of stove, replace the ignition module. put all back together and your done. Local parts store wanted $80+ for the module. PartSelect only $50 total cost and it hit my mailbox in TWO days! Thank you PartSelect.

Removed two screws per burner. Unhook wires. Putting back broke slide on connector and had to replace. That took longer than the whole job. I ordered the part before 3:00 pm and it was at my house tjhe next morning which was hard to believe. The instructions that come with part made no sense what so ever. Thanks for the quick service and I will be back.
Dave

Removed oven door. Removed three screws on ignitor holding bracket. Pulled out the range from the wall and reached underneath to access the wire nuts on the wires. Removed old ignitor and replaced with new one. Reconnected wires and then and replaced bracket and that's it. Works great now.

I called the local appliance parts store and they said it would cost $60-80 and take a week to order. I paid $16 and received my rack in 2 days!

I just ordered a new wire oven rack from you. When it came all I had to do was to remove it from the carton it came in and place it in the oven. It fit perfectly. Thanks

Removed two screws and disconnected the ignition wire. Then connected ignition wire to new burner and installed two screws

My husband took the oven door off then the bottom piece below the shelf took the old ignigter out put the new on in and now I have an oven again.

Un plug elect. Cord. Remove door by pulling upward removed back stove panel, un did 2 wire nuts leading to igniter. Un screw igniter inside oven at top next to burner pad. Interchanged old ignitor with new plug stove back in. Thats it.

Removed the top, 4 screws and pulled the contact wires off. Replaced the module and connected the contacts. Put back the screws and the top. When the stove was new it did not operate properly and we had a technician out, but naturally it worked for him. For the past 14 years intermittent operation has been agravating me. With the new module the burners have never worked so well.

Wow, ordered the part here and it arrived in 18 hours!! Job was fairly straight forward but the screw holding it in place was corroded and stuck. Several heating and cooling cycles with a torch and some spray lube and lots of patience and I finally rocked the screw lose.