ARR630LL (P1143403NLL) Amana Range - Instructions

I ordered the new part, which arrived in just 2 days. I did not pull the oven away from the wall, I merely turned off the electric, unscrewed the bad element, pulled it out enough to see the ends, and then I removed the existing wires using needle nose pliers. I put the wires on the new element, inserted it back into the oven wall, and screwed it tight. I turned the electric back on, and checked it out. Worked like a charm! Only 40 bucks (including shipping), five minutes of my time, and I avoided an expensive service call. :-)

Pretty simple. Turned off breaker. Lifted the top, cut the 2 wires. Going to the burner, put the 2 wire nuts on, and screwed the bracket in.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.

While trying to clean the oven, I decided to remove the lower heating element to make it easier. After removing the 2 screws on the bracket that holds the heating element in place, I pulled the heating element out only to short it out on the back of the oven and wreck the element. Luckly I was not injured or shocked, so if you need to do this, I recommend reading the owner's manual on how to property ground out the circuit first.

Anyways, to replace it, I just removed the lower panel on the back of the oven (roughly 10 screws). Installed the new element on the inside of the oven and screwed it into place. Then, connected the wires to the element from the back of the oven. Replaced the panel and turned the power back on.

In all, it took probably 15-20 minutes to fix and only cost me $37. I know that a minimum repair cost for this from Sears would have been $150, so definitely worth my time.

lifted the cover, unscrewed the ceramic wire fastners, put the new part in, and voila, job done and working perfectly

I took a couple of screws out that hold the bottom
element in place replaced the old one with the new one and fired it up. Worked like a charm and maybe this old stove will live on to make more Roast beef dinners.
If it been any easier my 10 year old grandson could have done it.

It was real easy. Removed two screws, pulled the element forward, removed to clip on wires, removed element and put the new element in place, replaced wires and screws, turned it on and up to temp. in no time. great service and quick delivery on getting the part.

replaced element

This repair took less than 5 minutes, literally! Two screws released the element, then unplugged it from two connectors. Then plugged in the new unit and screwed it into place. Cheap and easy!

The directions were very clear. I removed the heating element, detached the plug-in block by unscrewing the screw, then cut the wires about 3 inches from the block. I put the shrink-wrap collars around the wires leading to the new block, then attached the wires to the cut ends of the wires leading to the back of the stove, using the connectors provided in the kit. I couldn't get the collars to shrink as much as shown in the picture. I attached the new block to the stove top using the screw, plugged in the heating element, and it worked!
So the instructions were good, and the heating element is now working. The only problem was the heat shrink collars that go around the connectors: I couldn't get them to shrink much, but that doesn't seem to matter.

First I lifted the cooktop out of the countertop & removed the screws so I could access under the burners.Then I cut the wires for the old plug-in block & then stripped the wires.Next I connected the new wires with the wire nuts & then used a lighter to shrink wrap the wire nuts.Then I screwed in the new block & re-installed the screws for the cooktop.I put in the new burner & it worked just like new.

First I removed the one screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.

Removed burner and tray. Removed burner connector from stove top using screw driver.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.

Turned off the power to the stove. Removed the 'burners' and 'burner' trays. Removed the screw that secured the bad block. Lifted the top of the stove. Cut the two wires to the bad block., stripped the wires about 1/2", slipped the shrink tube over the wires. Connected the new block with two porcelan wire nuts. slipped the shrink tube over the wirenuts and heated it with a lighter. Closed the top and secured the terminal block clip with a screw. Turned the power back on: voila!

All the necessary parts came in the repair kit, delivery was timely. Very easy project.

First I removed the one screw that held the element in place. I then pulled the element out about 3 inches and cut the two wires...)
Assembled the block parts.
Installed shrink sleve and applied wire nuts to electrical connection to 2 wires then shrunk the sleve.
Did the above procedure for 2 heating elements.
They work very well now.