ARG7600WW-P1143345NWW Amana Range - Instructions

i had to remove quite a lot of screws in the bottom "pan" of the over to get to the igniter wiring. once it was apart, it was easy to see how to disconnect and reconnect the new igniter. the trickiest part is to put the igniter into the metal sheeted housing before you try to thread the wiring through to the plug at the back of the stove. overall, this is an easy rip out and replace process.

Removed two screws per burner. Unhook wires. Putting back broke slide on connector and had to replace. That took longer than the whole job. I ordered the part before 3:00 pm and it was at my house tjhe next morning which was hard to believe. The instructions that come with part made no sense what so ever. Thanks for the quick service and I will be back.
Dave

Philips is all that's needed. Remove the burners (2 screws each) lift off top of stove, replace the ignition module. put all back together and your done. Local parts store wanted $80+ for the module. PartSelect only $50 total cost and it hit my mailbox in TWO days! Thank you PartSelect.

I called the local appliance parts store and they said it would cost $60-80 and take a week to order. I paid $16 and received my rack in 2 days!

I just ordered a new wire oven rack from you. When it came all I had to do was to remove it from the carton it came in and place it in the oven. It fit perfectly. Thanks

I was surprised when I was able to find that the (10 year old) parts for one of the drawer slides of my stove were still available. However, I was disappointed that the small bolt that I ordered did not come with a nut. I was lucky to find one in a collection of nuts in my workshop, and so was able to fix the slide. However, I suggest that if you supply someone with a bolt, that you include the nut that is necessary to make it work.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

My husband took the oven door off then the bottom piece below the shelf took the old ignigter out put the new on in and now I have an oven again.

Wow, ordered the part here and it arrived in 18 hours!! Job was fairly straight forward but the screw holding it in place was corroded and stuck. Several heating and cooling cycles with a torch and some spray lube and lots of patience and I finally rocked the screw lose.

I removed the cartridge from the range and used a screw driver to remove the screws holding the burners assembly in the housing. (Some prefer to remove the burner from the top by removing the two screws, but I've had trouble realigning the parts that way.) I removed the ignition wire and the screw holding the bad electrode in the burner. I then installed the new electrode, attached the ignition wire, put the burners assembly back into the housing, and put the housing back into the range.

Remove the cover over the burner, two screws at the rear, this exposes the burner tube cover, one nut at the center. Three screws will remove the holder for the igniter. I had to remove a sheet metal cover underneath the oven( pull the drawer out) to gain access to the plug for the igniter. A good tip on this is the same valve controls the broiler and the oven, if one works and the other doesn't, it's the igniter. If neither works the gas vale may be the problem.

Removed two screws and disconnected the ignition wire. Then connected ignition wire to new burner and installed two screws

order new ones, got the model#, also thanks too my husband he look on line and found your company thank you so much. i will tell my family, and friends about your company thank you again great job. lisa

Un plug elect. Cord. Remove door by pulling upward removed back stove panel, un did 2 wire nuts leading to igniter. Un screw igniter inside oven at top next to burner pad. Interchanged old ignitor with new plug stove back in. Thats it.

First I removed the knobs on the range, then the front cover and then removed the two screws that hold each burner in place. I removed the top and removed the Module and started replacing the burners and front ocver and knobs. The Module worked GREAT. Thanks for your fast service in getting me the parts.