ACF3355AB-PACF3355AB1 Amana Range - Instructions

I unscrewed the ignitor from the gas supply. Unplugged the ignitor. Plugged the new ignitor in and screwed it back in place to the gas supply. It could not have been easier!

This was VERY easy and I've never worked on this type of appliance before.

First, take off the grate, thermal plate, etc that are resting on top of the stove (this is all the stuff you take off to clean the stovetop).

Then, carefully unscrew the two screws holding the burner to the gas pipe. Grab the screws and set them aside so they don't fall back into the stove, then pick the burner up off the stove.

once you have the burner a few inches above the stove surface, wiggle off the single wire by grabbing it on the metal part (not by the wire) and gently wiggling it off.

Grab new burner, push on wire and sit it on stove, use a finger in the gas pipe to align it and put the two screws in. you're done.

cleaned out pad area with an awl. then the pads just slide in.

This was very easy to install. I removed the screws that held the trim in and took it off and put the new one on and screwed it on. Within 5 minutes it was complete. I just wanted to say that my wife was very discouraged because she couldnt get the discoloration off the trim. So she went on the internet and found partsselect.com. I gave here the model number and from there it was easy to find the part and order it. Within 5 days we had the part delivered and installed. Thank you because it was so easy.

A Home Depot employee advised me on how to enter all my oven information found on the front of my oven on parts.com. I submitted parts information as stated, also very easy. My parts arrived 3 days later. I used a screwdriver & pliers, it took less than 15 minutes. Very simple and the entire process from order to installation went like clockwork. I would definitely order in the future. Thank you.

Replace the igniter. Removed 2 rear screws that secure bottom oven pan. Removed pan. Ignigter is located in center rear by 2 screws. Removed the screws and pulled ignigter out from rear. There us a prong connection that when pressed will release igniter. Don't touch new ignigter without gloves on. Will reduce life. Plugged in new ignigter and secured w 2 screws. Turned on oven to ensure problem was fixed. After 30 seconds, oven ignited. Replaced bottom oven pan. Tadaa!

Removed the two screws that hold the element in place. Disconnected the wire to the electrode. The screw holding the electrode to the burner plate would not unscrew so I had to drill out the screw in order to replace it with the new ignition electrode. A little more time involved but if the screw would have come out it would have been a 10 minute job.When I ordered the part from you it came very quickly and I will certainly use you again when I have any other issues.

remove grate - flip upside down - be sure holes are clean and dry - using toothpick, swab some RTV sealant into the holes and a bit on the pads ... insert pads till they seat - be sure to hold in place till all air is evacuated - wipe excess RTV with paper towel...DONE

I removed all 4 burners 2 screws holding each,replaced the ignition module,wire for wire,reassembled after cleaning the stovetop.I,m my wife's hero.

Removed oven door, removed bottom of oven, removed old igniter, installed the new one and plugged it in in the back of the stove. Installed oven door and it works fine. .

I was surprised when I was able to find that the (10 year old) parts for one of the drawer slides of my stove were still available. However, I was disappointed that the small bolt that I ordered did not come with a nut. I was lucky to find one in a collection of nuts in my workshop, and so was able to fix the slide. However, I suggest that if you supply someone with a bolt, that you include the nut that is necessary to make it work.

It didn't. The grate pads (PN# PS389174) were too small for the grate (W10311216) and wouldn't work. (PN# recommended by Whirlpool parts department) The pads were smaller in diameter and shorter. Yes I could have glued them in, but because of the size the pads would be flat in no time. The only thing I could order from KitchenAid was the total grate. I ordered the pads late December, they were backordered. I got them the 1st week of February. I tried getting through to Whirlpool by calling to see if there was something I could reorder, but no luck, couldn't through. Am I unhappy? Oh some, but I handle it. Its not the first time I have been rode hard and put away wet.

I removed the cartridge from the range and used a screw driver to remove the screws holding the burners assembly in the housing. (Some prefer to remove the burner from the top by removing the two screws, but I've had trouble realigning the parts that way.) I removed the ignition wire and the screw holding the bad electrode in the burner. I then installed the new electrode, attached the ignition wire, put the burners assembly back into the housing, and put the housing back into the range.

Installing new igniter was very easy. The problem I had was removing the screws. The range is 18 yrs old. The screws were stuck from yrs of use. Especially in the oven cover plate. I used w- d 40 it didn't work. I decided to take a 2" putty knife and push it under the screw head to release it and it worked. They came right out. The igniter screws were also difficult to get out. Once those were removed, I pulled the stove out, turned off the gas and the electrical plug, removed back plate unplugged the old igniter and connected the new one. Easy, peasy. Turned gas on etc. Tested the oven to be sure it worked. Turned oven off.Then put it all back the way it was. Done! The igniter install was simple and qiuck. The time problem was the screws.

I took the door off, then took the bottom out removed two screws, unplugged the old igniter and installed the new one. I turned on the oven and tested the new igniter and then replaced the bottom and oven door.