ARG7600LL-P1143339NLL Amana Range - Instructions

looked at and saw that ignitor was cracked,saw simple repair ahead. just needed the right part . Without part , select simple ,and easy selection, i might not have ever found the right part. as i said before finding the right part is 90 percent of the job and they made that an easy task .

of course if you want me to describe in detail, took out the pan saw the bad ignitor, removed 2 serews, disconnected 2 wire, the reassembled in the opposite direction. 30 minutes tops. I am sure this saved me at least 150 bucks for some "so called reparman" to do the same job, Most people do not realise that they have more education than most of these "repairmen". The only advantage these "repair people" have is acess to schematics and part numbers. Part select is a good start on putting this information in the hands of us average "idiots" as I am sure the repair folks call us when we pay 200 bucks for a 30 dollar job.

I had done this before, but a while back, so it took a little longer to disassemble and find the igniter. Once there, easy to troubleshoot with a meter. Reassembly was only a few minutes and part of that was finding a new nut, since I lost one. I had to remove the storage drawer, then remove a metal cover to get at the connections. I tested the power to the igniter and found it to be OK. I tested continuity and had some but very low. Pulled the diffuser and cover off burner to locate igniter. Ordered part,put it on and reassembled everything. Working fine.

First I had to take the drawer completely out of the stove to reach the igniter. I then removed the screws that held the igniter in place and removed it. I had to slightly modify the replacement part by squeezing it together to make it fit into the same space. I put the replacement igniter in place and screwed it down; put the drawer back in the stove and turned on the over to see if it would light. Bingo, job done!

Simple install - 6 -7 screws one nut. Once replaced oven worked good as new. Part shipped from PartSelect actually better than one installed by repairman 4 years ago - fit like an original part.

Thanks PartSelect.com

Remove the racks
remove one nut that holds the heat deflector
3 screws that hold the igniter
remove the drawer
remove 2 screws holding a heat shield in place.
unplug old igniter and reinstall

I used your instructions

We removed the oven protective shield, took out the broken glass (very carefully) and replaced it with the part shipped. Then, we replaced the protective shield and it was done.

shut off gas at tank, pulled stove out from counter area to gain acess to back, removed oven door removed removed screws holding igniter unit in place, i then removed the stove rear panel to get at the wiring for ignitor,remoded old part returned to front and installed new part, checked voltage then re-connected new wires, turded gas back on and tested oven, oven came on less than a minute, put rear panel on stove put door back on and put stove back into counter area, stove works like new.

Removed the three screws holding the igniter, pulled the old one out and plugged in the new one. Very simple.

Bought a new one. . Three years later =)

First turned off power to oven, Took burner out by lifting up and pulling out, then pulled out wires attached to the oven and igniter, removed two wire nuts and disconnected the wires then removed burner assembly from oven. With screwdriver and nut driver removed old igniter from housing and put new one in place, tightened up screws carried back to oven reattached wires with wirenuts and feed wires back into oven, then put burner back carefully silding igniter into hole in back of oven. Turned power back on to oven and worked nice. Took all of 15 mins to complete.

diagram on website was very helpful. simply unscrew two screws,remove and replace electrode and works perfectly.
Ordered one day arrived next with standard shipping installed before next day supper awesome service

very simple repair, the oven had the issue about ten years ago, just removed drawer ,removed two screws holding cover plate unhooked power and disconected plug. removed element screws and pulled out old element from holder and inserted new one. re attatched element holder, cover plate, and put drawer back in. works great !!!
My parts wrere shipped promptly and arraived in great condition, stove looks and works like new again

Removed oven grills and top of burner pan. This exposed the igniter. Removed 3 phillips head screws from igniter bracket. Slid old igniter out the back end. Removed utility drawer. Removed two screws from back pan covering igniter plug-in. Unplugged igniter, removed from range. Handling of igniter is tricky..do not touch black end. Slide new igniter into the bracket, feed wire with connector through hole in back (where igniter was removed from), install the three screws for the bracket (your new igniter is now secure), from the bottom, plug in the new connector it only goes on one way. Re-install pan with two screws. Put utility drawer back in..job is complete!!

ordered new broiler pan