ARG7800LL-P1143385NLL Amana Range - Instructions

cleaned out pad area with an awl. then the pads just slide in.

left side hinge was broken. I removed 2 screws to release the old hinge and replaced it with the new hinge.
Part select.com made it easy to pick out the part from the diagram supplied on the web site. After it was ordered it arrived 2 days later.

opened up the oven to locate the position of igniter

disconnected igniter and checked the continuity of the igniter to find that I had an open circuit

once I found out the igniter was no good I google for appliance parts and found parts select had the best prices that I could find. I called a couple local parts stores and there prices were definately inflated. I chose to go with parts.select.com
I receive the part in two days! I installed the new part within 15 minutes and turn on the oven to have it light almost instantly. I won much praise from my wife. Parts.select.com recieves my praise for ease and quickness of part delivery.

I read on this site about someone who had my same problem. He ordered and installed a new spark ignition module and after installation the stove worked fine. So I ordered a part # PS2034431 Spark Ignition Module for my Amana stove. I installed it, and it worked just fine, really for the first time since I bought the stove new. Oh well...
Taking the stove apart took a bit of study to find how to get it right, and the clothes pins were to keep the wires from slipping back through the stove top as I was putting it back on before actually hooking up the piezo units. The instructions that came with the spark igniter were pretty useless (not wrong, just useless), but carefull notes while taking the bad unit out and where each wire went made the replacement rather easy. The really tough part was removal of the burners - the small screws had deteriorated over the last 7 years, so I had to drill two of them out. I replaced all of them with stainless steel screws. This cost an hour of my time plus a trip to the hardware store.
But as I said... the stove now works fine really for the first time. Way to go, Amana!
I trust this igniter will last a lifetime.
And certainly, reading about the same problem I had and easily finding the part was a welcome treat on this site.

Had to take entire back panel off, to disconnect wiring. Once disconnected, removed two screws holding up igniter in oven. Pulled it through and removed from holder, Be careful new igniter very fragile. Reconnected, put panel back on, then turn on to verify, all went well, fully operational.

I removed the two screws and pryed out the old hinge. I then put in the new hinge. The new one fit well. I went to screw it in with the supplied screws. The screws not only did not fit the hole tapped in the hinge (too big, different tread) but both screws were different from each other. They were different sizes and different types all together. I tried re-using the screws from the originol hinge but they also did not fit. I then got my own self tapping machine screws and finished the job. This job should not have been that hard. If they had supplied the correct screws, It would have taken all of five minutes.

Removed the two screws that hold the element in place. Disconnected the wire to the electrode. The screw holding the electrode to the burner plate would not unscrew so I had to drill out the screw in order to replace it with the new ignition electrode. A little more time involved but if the screw would have come out it would have been a 10 minute job.When I ordered the part from you it came very quickly and I will certainly use you again when I have any other issues.

First turn off power to stove with breaker or unplug it. Then remove three screws under the front of cook top, and lifted up cook top from the front. Then brace it up with a stick about 20 inches long so you can work. Now locate the latch at the front of range. Next get some paper and labeled where each wire is connected by color. Remove wires from old part, next take out two screws by the front of part. Remove a clip on left side of part that is holding the wires. Take old part out and replace with new part, put back the two screws in front of part. Next put the wires back on using the list you made. Then replace clip to hold wires. Now turn power back on,or plug it back in. Reset clock and your done.

A Home Depot employee advised me on how to enter all my oven information found on the front of my oven on parts.com. I submitted parts information as stated, also very easy. My parts arrived 3 days later. I used a screwdriver & pliers, it took less than 15 minutes. Very simple and the entire process from order to installation went like clockwork. I would definitely order in the future. Thank you.

I took out ruined racks. Cleaned the oven, getting rid of all the melted plastic. Once oven was sparkling clean, I slid in the new racks I bought from here. (The easiest part).

* * * *
I'm very thankful to have found this site. My oven has been "out of order" for over 3 years. It's so nice to be able to use it again! =)

I live in a small town in South East Colorado. We have just a Walmart and Sears and a few smaller hardware stores. I checked all of them to try to find this 25 1/2 inch Fluorescent Light Bulb, and nobody carried one. I would have had to drive 70 miles to find one. The Service of Partselect was wonderful and the bulb showed up in just 4 days. I was lost without this light. I have bought a few other items for my older appliances in the past from Partselect. com and was very happy with the service and how easy the web page is to navigate. .

Repair can be done through the oven after removing the dip pan on top of the oven burner. The drip pan slids out - no tools needed. Remove 1 screw that holds the element close to the burner and 2 screws that hold the element cover to the stove. Remove bottom drawer and remove wire nuts from element wires. Reverse the process to install new element. Care must be taken to avoid damage to the element as it can be easily broken. I cut and stripped the wires coming from the stove valve as they were not in good shape after removing the wire nut.

First, I unplugged power to the stove. Next, I removed the grills, ceramic burner discs, gas knobs, and glass plate (under the knobs). Next, I removed the 2 screws exposed by the control knobs. Next, I removed the 2 screws holding each burner assembly to the cook top. I then unplugged the wires attached to each burner assembly and set the assemblies aside. Now I was able to remove the top. Once removed, it was very easy to locate and remove the bracket holding the old sparking module. Then it was just a matter of removing the wires from the old module and attaching them to the new module... attaching the new bracket to the stove and then re-assemble the cook top. Honestly, this was a very simple repair... and probably took me longer to describe the steps than actually execute.

I took out the oven racks. There are 2 cross head screws and 1 screw with a hex head holding the igniter. Pulling out the igniter carefully and the wire nuts also came out. Replaced the wires using the existing wirenuts and slid the igniter into place. Replaced the 3 screws and DONE. Wish the igniters were a little cheaper as this is the third one to go weak. The new one draws about 3.2 amps while the old one only drew 2.85Amps, not enough to open the gas valve. Oven works Fine now. Thanks parts select for the rapid delivery.

i read other stories and found after checking rotating heat switch with ohm meter found the igniter was the problem, pulled up on door and it came off, found bottom of oven pulled up and out, removed wing nut from deflector and two bolts and one wiring connector, just reversed removal to install new igniter and all complete, took about 20 minutes,