AGDS901WW Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- martin from portland, OR
- Parts Used:
- WP74011278
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
oven light replacement
bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willliam from Goldfield, IA
- Parts Used:
- WPY0314907
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gears and gear box top case cracked
Take top cover off take gear box cover off. check all gears for wear and clean all of above. Be sure you identify all parts needed before you order plus assembly grease!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Westlake, OH
- Parts Used:
- R0706011
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Door wouldnt shut evenly.
Ordered hinge, went to Sears bought some tools to finish manufacturing the hinge, tapped out the screw hole, installed the hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Mountain Ranch, CA
- Parts Used:
- R0706010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven door hinge broken
Discriptions provided by others in this section made it easy and there is little additional insight I can add. The part was delivered the next day. I don't reply to these requests for comments, as providing what I paid for is the expectation. But, this outfit did a good job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from UKIAH, CA
- Parts Used:
- 786324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Oven would not light.
Removed old igniter and replaced with new one.Tested oven and it went on. You need a phillips screwdriver to remove two screws and a small socket for the third screw to remove the igniter cage. Then pull out the wires from under the oven and disconnect. Reverse procedure to install new igniter. Reuse original connectors. Be very careful with the igniter because the tip is very fragile and can break easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Quincy, FL
- Parts Used:
- WPY0307363
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old filter replacement
Removed grill cover, took out old filter and placed new filter, placed grill back over filter. Back in business!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Sapulpa, OK
- Parts Used:
- 786324
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
Lower Bake Ignitor would glow, but would not ignite flame.
First, my wife and I pulled out the oven from wall to disconnect electric plug and, also with a wrench; I shut off the gas connection on the wall. I then removed front door of the oven by pulling up on door to have easy access to lower part of oven, and then removed pan to get to Igniter. Removed the three screws on cage that supported the Igniter and, I also had to remove several screws to the manifold and bottom pan that supports the manifold so that I could disconnect Igniter. I then was able to pull out old Igniter and, reconnect the new one. After that, I reinstalled everything in reverse. Before pushing oven back into wall; we made sure the new igniter worked. It worked just great. My wife and I were so happy and proud that we done it our self, and not have to call someone to do it for us. It took me and, my wife about an hour and a half to complete the job. I believe the reason it took us as long as it did was because we really didn't know what to expect. Now that we know; I am sure that we could do it again in 30 to 45 minutes. Dave & Marsha; 8/23/2013
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeffry from Sussex, NJ
- Parts Used:
- 786324
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Oven no longer came on
Replaced the igniter. Took out the 20 screws holding the bottom plate of the oven. Removed the igniter and gas tube mounting screws and bracket. Took off the wire nuts that attached igniter to stove wiring. Carefully installed new ignitor, using reverse of the steps above. Igniter tip is very fragile, so beware as you handle. All went very well, and oven now works like a charm
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fletcher from Greenville, SC
- Parts Used:
- 786324
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Ignitor would not ignite the oven
Removed the oven doors for access; removed the burner onto which the ignitor is attached, disconnected the electrical wires (power off). Reversed the procedure to put it back together. We are now cooking with gas again. Thanks. Fletcher
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- VICTOR from MOUNT PROSPECT, IL
- Parts Used:
- 786324
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Socket set, Wrench (Adjustable), Wrench set
Screws Were Rust6Ed, Melted
Used grinder to cut the screws. All 4 screws had to be cut to remove from burner assembly. Once this was acomplised it went fast with no problems
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Blair from Florence, NJ
- Parts Used:
- 786324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old igniter lost power to ignite gas..
The first igniter was received broken. A replacement was received within 5 days. It was very easy to install once the protective cover was placed over the igniter end. In my opinion, this part should be sold with the protective cover already in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Milwaukee, WI
- Parts Used:
- 786324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
stove sometimes would not light or took really long and did not maintain heat
We unplugged the stove and turned off the gas. We slid the oven door off just to make it easier. Unscrewed 3 screws holding the igniter in place. Pulled the igniter out from the back of the stove. Disconnected the two wires. Slid the new igniter in the holder. Rewired it and slid it back into place. Put the screws back in and it was done. Plugged it back in, turned the gas on, tried it out and presto! It was perfect! Lit immediately and strong and now i have a brand new 20 year old stove. lol Happy girl! And this was done by 2 50 year old women!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wesley from Norman, OK
- Parts Used:
- WPY0314907
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven not heating, F3 trouble code.
Removed back panel, unplugged sensor, removed sensor from inside oven (2 screws), replaced with new part.
Was this instruction helpful to you?
Thank you for voting!