Models > S1050EH-Z > Instructions

S1050EH-Z Admiral Range - Instructions

Jump to:

All Instructions for the S1050EH-Z

Customer:: William from Florissant, MO
Parts Used:: WPY04000041
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

The original bake element burned out

1. Removed racks 2. Removed two screws holding in the bake element. 3. Gently pulled out the element exposing the two wires connected to it. 4. The two wires were held by a clip connection. 5. Removed the wire clips holding the wires. 6. Attached the clips to the new element and re-installed the element. New problem: The element did not heat up. A repairman informed me that the selector switch was damaged during the burnout- that switch was no longer manufactured and was discontinued. Whirlpool company was checked and indicated that there was a new part # 7403P023-60 but that was discontinued too. I was able to get the element working by moving the selector switch to the "Bake" position and then moving the switch about 1/4" in the clockwise direction. The element heated and the oven works at least for now as I search for a replacement part. PartSelect was an invaluable aid and helpful all along the process.

Was this instruction helpful to you?

Customer:: Matthew from Chippewa Falls, WI
Parts Used:: WP7803P058-60
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Broken Door Spring

Slid oven out from counters. On each side there are 3 screws on the front and three screws on the back holding the side piece on. Once off, the spring was very easy to get at and replace. I had only one broken, but replaced both anyways. I think it took longer to clean the sides of the oven that haven't been touched in years than to replace the springs. This job was very simple and easy.

Was this instruction helpful to you?

Customer:: Wallace from Lowell,, AR
Parts Used:: WPY04000048
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Broil element burned out

Removed the oven door, removed old burned element, installed new element. Turned CB back on and tested oven. Reinstalled oven door. Straight forward and easy to follow directions with new element.Local appliance part house said the element was no longer available. Thanks to you I did not need a new oven. Very easy replacement job with normal tools.Thanks

Was this instruction helpful to you?

Customer:: Dennis from Oak Lawn, IL
Parts Used:: W11122006
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Burner was always in high temperature.

Pulled the range away from the wall and took out all the screws of the back panel. I had two different screws. Removed the dial and took two screws out behind the dial. Carefully removed the wires and placed them on the new switch. Screwed switch to panel, replaced dial and put the back panel back on range. Pushed range back into place.

Was this instruction helpful to you?

Customer:: Robin from Vanderbilt, PA
Parts Used:: WPW10245259
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

I had a power serge and it burned the Plug at the termial block and melted a few wire.

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

Was this instruction helpful to you?

Customer:: Deborah from Hodgen, OK
Parts Used:: W11122006
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Burner stayed on "high", could not adjust heat

I UNPLUGGED STOVE, removed panel covering the controls, removed the knob on front and the two screws there that hold the control in, inserted new control and replaced the two screws on the front that hold it onto the stove, used needle nosed pliers to unplug one connection at a time from the old control and onto the new control in the back. When I had all connections plugged onto the new control I re-installed the panel cover with a screwdriver, plugged the stove back in, and the burner is now working good as new!

Was this instruction helpful to you?

Customer:: Jennifer from Albion, NE
Parts Used:: WPW10196405
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins

Drip bowls tarnished.

Remove heating element coils. & old drip pans. Install the new drip pans and reinsert the heating elements and insure all elements were level. For aesthetic reasons I replaced all the drip pans - 2 x 8" & 2 x 6".

Was this instruction helpful to you?

Customer:: Dennis from Oak Lawn, IL
Parts Used:: W11122006
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Burner was in full hot.

Turned off the power. Pull the range away from the wall and removed the eight screws holding the cover in place. Carefully pulled the wires off the old switch. Removed the old switch and replaced it with the new. Put all the wires on and replaced the back cover and was done. Burner works fine. This part replaces a lot of different number switches.

Was this instruction helpful to you?

Customer:: myrna from homestead, FL
Parts Used:: WPW10196405, WPW10196406, WPY04000036, WPY04000035
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Elements did not fit properly.

Ordered the parts, installed.

Was this instruction helpful to you?

Customer:: Judy from Framingham, MA
Parts Used:: 7801P030-60
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Somehow one of our oven racks was missing - maybe taken inadvertently from beside old refrigerator when it was removed.

We just installed the new rack in the oven. The amazing thing (after many unsuccessful attempts to find the correct rack) was having a friend recommend partselect.com. The gentleman I spoke to was extremely knowledgeable, helpful and efficient. We had our new rack 2 days after placing the order. We thought that kind of service didn't exist any more! Thank you so much. Now we can make 2 pizzas at the same time!!!

Was this instruction helpful to you?

Customer:: Dallas from Arlington, TX
Parts Used:: WPW10196405, WPW10196406
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

replace the cook stove's drip bowls instead of cleaning them

I removed the burners and then the older drip bowls of the cook stove--and then I put on the new drip bowls and put back on the burners. My mechanical skills were sufficient for the replacement of the drip bowls.

Was this instruction helpful to you?

Customer:: Dallas from Arlington, TX
Parts Used:: WPW10196405
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

I needed to replace to two 8* drip bowls on the kitchen range

(a) I took out (and threw away) two stained 8* chrome drip bowls on my kitchen range; (b) ti put in two new 8" chrome drip bowls on my kitchen range. I'm pleased that I was equal to the task.

Was this instruction helpful to you?

Customer:: Karen from Kettering, OH
Parts Used:: WPW10196405, WPW10196406
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Stove needed new bowls

Just dropped in

Was this instruction helpful to you?

Customer:: gizella from mays landing, NJ
Parts Used:: WPW10196405
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Old dirty drip pans

Removed heating element, installed new drip pan, replaced heating element. Was amazed at fast delivery - ordered in afternoon, arrived fed ex next morning!

Was this instruction helpful to you?

Customer:: Alison from Carnation, WA
Parts Used:: WPW10196405, WPW10196406
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

The drip pans needed replacing.

Put in the new drip pan -- which are really nice shiny ones.

Was this instruction helpful to you?

All Instructions for the S1050EH-Z