A31713XATL Admiral Range - Instructions

This website easily diagnosed the probable problem. We ordered the suggested part and my husband replaced it, despite a slightly eroded, rusted screw that was stubborn to remove, in about 20 minutes. The oven is working perfectly. With tax we spent about 50 bucks. I was sure we needed a new oven. We, ironically, celebrated by going out to dinner!

removed the old defective ingniter and installed new igniter turned on the ove n and wala, it was like brand new.

Checked troubleshooting guide on website / ordered part / replaced part by removing two screws in oven on bottom pan/ removed inside oven bottom for easiy access/ removed two screws from bracket holding down the heating element/separated the electrical plug in back releasing the wires to heating element/ installed the new element with two screws / connected the electrical plug/ installed the bottom panel inside oven / installed two screws inside oven on bottom panel. Checked operation of unit- gas lit ok - pushbutton panel did not increase heat seting properly/ dismantled the control panel / dismanteled the circuit board / found remains of several roaches inside circuit board recess/ cleaned all pushbutton points and re-assembled unit - all worked fine except when oven burner went off - the gas valve would not shut off completely - leaving a small flame burning at the gaaas valve orifice "DANGEROUS". I checked troubleshooting guide again / ordered a new valve - installed - (did not come with a new Propane orifice ) - had to use old one ( should have either asked me or just sent one when I ordered) - received new valve - installed with old Propane orifice - all works well now.

First I unplugged the range, turned off the gas to the oven and disconnected the gas line from the oven. I pulled the oven out to gain access to the rear of the unit and unplugged the old igniter. Next, I removed the oven door, removed two screws to the floor of the oven and removed it. I then removed the metal covering above the gas component allowing full access to the igniter. I removed two screws from the igniter and removed it. I positioned the new igniter and replaced the two screws. I replaced the covering over the gas component, replaced the oven floor and put the oven door back on. I went to the rear of the unit and plugged in the new igniter. I then reconnected the gas line to the oven range and checked for leaks, No leaks were found and I pushed the oven unit back into place. I pushed the Bake button and the igniter started igniting the oven.

Job completed.

1. Turn off the gas (propane)
2. Unplug the oven.
3. disconnect the gas line and pull the oven out.
4. remove the back panel to access the igniter.
5 disconnect the igniter.
6. unscrew igniter/gas assembly and remove from oven (two screws).
7. unscrew igniter (two screws)
8. replace igniter with new.
9. reassemble in reverse order.
10. turn on stove.
11. Happy wife, happy life.

We took the interior floor out, pulled the stove away from counter, before that turned all electricity to the house off. Then we unscrewed the ignitor inside then underneath unplugged it and plugged in the new one, cleaned to oven and screwed the ignitor in and replaced the interior floor and we were done.

My oven would not work. It took longer & longer to fire, finally died. I did an online search & found partselect.com, with it's very helpful troubleshooting info, and somebody posted info that 80-90% of the time it's the ignitor that has failed. I ordered it Sunday night, it arrived Tuesday. I took the door off for easy access, took the bottom of the oven out, removed the flame shield and replaced the ignitor. I tested it and it worked! The hardest part was moving the stove away from the wall & threading the ignitor plug thru the back of the oven. The cheapest appliance repair visit would have been $89 + cost of parts. Sears charges $129. I think I saved at least $100, thanks to partselect.com.

Tested power coming into unit,then tested power going to igniter,both of which were good.Did a continuity check of igniter element and found it to be bad.Ordered one from PartSelect,recieved it in minimum time,removed the old one,installed the new one,works like a champ.

I started with pulling the base of the oven to examine the mechanism underneath. The hardest part of the whole thing was working the wire connection past the metal back of the oven. It required prying the metal away from the frame rail and wedging the wire connection through. Other than that it was unplugging the old, plugging in the new, and a few screws to reattach the igniter, heat sheilds, and oven base.

First I called a local repair shop and after getting a 325.00 repair estimate I looked up your website and discovered that I could purchase the part for 46.00 dollars and followed the do it yourselfers imput Now thats what I call a savings

We hired the neighborhood handy man, and he was able to repair the oven in about 15 minutes. I order the part and received it the next day. Excellent Service!!

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Changed the igniter

I opend the bottom cover, which had for screws then , opened 2 screws that atached the igniter to the main gas pipe and pulled the whole wiring out and disconected the wiring , ordered the igniter two days later, I put the whole thing together in less than 5 minutes . put back the cover. and I tried it , everything was cool , accutaly hot and working .

Screwed in light bulb and glass protector