A1500PRW Admiral Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Greg from Versailles, IN
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
large burners not working
Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so you have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dicky from mcrae, AR
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace burner coil connector
Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be sure and disconnect power before starting!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Royce from Rio Rancho, NM
- Parts Used:
- WPY04000035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old surface element burned out.
I ordered and received the replacement element, then unplugged the old one and plugged in the new one.
Job done.
Job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from San Francisco, CA
- Parts Used:
- WP74010761
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
My heating element stopped working properly and one day just make a pop and stopped working altogether.
I followed the advice givin on the parts select website - it made it totally easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ana from Riverside, RI
- Parts Used:
- 7801P151-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing one oven rack
put it on, perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gene from kent, WA
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner not working
burner was shorting out replaced part works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Union Mills, NC
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner would not heat up the connection was bad
loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- myrna from homestead, FL
- Parts Used:
- WPW10196405, WPW10196406, WPY04000036, WPY04000035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Elements did not fit properly.
Ordered the parts, installed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dallas from Arlington, TX
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace the cook stove's drip bowls instead of cleaning them
I removed the burners and then the older drip bowls of the cook stove--and then I put on the new drip bowls and put back on the burners. My mechanical skills were sufficient for the replacement of the drip bowls.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Kay from North Charleston, SC
- Parts Used:
- W10196406RW, WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner coil was falling apart.
Used new plug in coil burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Vanderbilt, PA
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
I had a power serge and it burned the Plug at the termial block and melted a few wire.
After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elroy from Atwater, MN
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
burner not operating or intermittently
Shut off power at breaker box. Removed top burner unit. Removed old receptacle (Mounting screw was rusty so I drilld out the old one.) Cut wires from old unit. Stripped wires back on old unit. Attached old and new wire with ceramic wire nut. Attached new unit. Reinserted top unit. Reconnected power and "voila". Wife was smiling again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Norristown, PA
- Parts Used:
- WP74010761
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Heating element for baking not warming up
In removing the old element I discovered that one wire had completely separated from the connection to the element. I fished out the wire, clipped off the old, burnt out connector, crimped and reattached a new connector and connected to the new element. This was a very easy job. The hardest part was determining which switch at the electrical panel corresponded to the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Desoto, MO
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
two of the burners were working intermittently
I shut off the breaker checked for power then cut old plugs making sure to allow a little slack. Tightened down wire nuts put on a couple wraps of electrical tape and that was it. Burners work great now I would reccomend this product to anyone with a similar problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willis from Anaheim, CA
- Parts Used:
- W10196406RW, WPW10196405, 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Two old Surface Burner Receptacles needed to be replaced.
I followed the instructions given on your great site. Thank you so much.
Was this instruction helpful to you?
Thank you for voting!