CREA400ACL Admiral Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Leticia from Sunnyvale, CA
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bakeing element caught fire.
First I turned off power to the range at the fuse box (very important-The last time I didn't do this and ended up paying a repairman $150.00 to replace the damaged connectors). I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then connected the new element, pushed the element back in and replaced the screws. Turned the power back on and tested the element. The whole job took about 30 minutes because I had trouble disconnecting the old element. I used the flat end of the scrapper to push against the connector while I pulled the element out. Normally it would take only about 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lowell from Hardin, KY
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Couldn't find correct drip bowls that fit.
Removed old drip bowls, removed burners installed new drip bowls,installed burners. They fit perfect and I received them two days after ordering.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Marietta, GA
- Parts Used:
- WP74003019
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element burned out.
Turn off breaker.
Unscrew old element, disconnect wires.
Connect wires to new element, tighten screws.
Breaker back to ON.
Done.
Unscrew old element, disconnect wires.
Connect wires to new element, tighten screws.
Breaker back to ON.
Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bert from S. Easton, MA
- Parts Used:
- WP74003019
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element Melted
Unplugged stove, unscrewed element pulled element out about 3 inces and disconnected element. Took model of stove looked on line for part. PartSelect had the best price and easiest web site to order part. Ordered part about 4pm and received part in 2 days. Took element out of box plug into connections and screwed the element back in. Plugged stove in and worked perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Yukon, OK
- Parts Used:
- WP74003019
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
snapped element
switch off the range. undo the two screws & unplug the two tabs. Replace with new element, connect two tabs, screw back in place. done!
recieved my replacement part the next day after ordering
recieved my replacement part the next day after ordering
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Ottawa, OH
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element burned out.
First I removed the two screws that hold the element in place. I then pulled the element out aobut 3 inches and disconnected the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Schertz, TX
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bake element would no longer heat up
I unplug the stove first. Then took off two screws that held the bake element in place. Pulled off the connectors using the pliers. Had to use pliers because they were really snug. Plug in the wires to the new base element. Crimped down the connectors a little bit to make sure they were snug. Inserted the bake element back into the holes at the back of the oven. Put the two screws back in. Plugged the oven back in and turned it on to make sure it worked. Lastly, tossed the old bake element in the trash. Really easy job. Glad I didn't pay anybody to do this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tawnia from SHOW LOW, AZ
- Parts Used:
- WPW10259868, WPW10196406, WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
surface element needed to be replaced along with all the drip Bowls
take out the old put in the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Medford, OR
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My oven sparked, then wasn't working, so I turned to the internet.
I received the new element on the third day, followed simple directions, and voila! I'm baking again.
First I unplugged the stove. Important!. Then with a phillips head screwdriver I removed the two screws at the back of the oven. The transition from busted to new was easy because there was a slide-in connection to the wires, not screws. The best advice was sticking duct tape on the wires so they wouldn't go back into the inner sanctum before I was able to attach the new element. Hey, I'm a 72-year-old grandma, and it was easy!
First I unplugged the stove. Important!. Then with a phillips head screwdriver I removed the two screws at the back of the oven. The transition from busted to new was easy because there was a slide-in connection to the wires, not screws. The best advice was sticking duct tape on the wires so they wouldn't go back into the inner sanctum before I was able to attach the new element. Hey, I'm a 72-year-old grandma, and it was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicki from ELSIE, NE
- Parts Used:
- WPW10196405
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Drip pans were old and with burnt on food that I couldn't get off. Disgusting!!
No problem Took off old ones and replaced with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kiara from JACKSONVILLE, FL
- Parts Used:
- WP74003019
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Baking Element won't heat to bake.
I had the problem before and had to call in a Tech to repair the baking element in my oven. It cost me $150.00 for the repair. This time I decided to do the repair myself, so I went online and found this site The instruction video made it very easy. I am very proud of what I was able to do without calling a Tech. My oven works like new, It only cost less than $40.00 for the total repair. I am so glad this site were there when I needed them.. Thanks a Lot..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frances from MOREHEAD, KY
- Parts Used:
- WP74003019
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace broken bake element
Unplugged the range. Took our the oven shelves. Unscrewed the bars holding the broken bake element to the back of the oven wall. Gently pulled out the wiring to which the bake element is attached. Slipped the ends of the broken bake element off the ending on the wiring. Then slipped the ends of the new bake element over the ends on the wiring. Then pushed the wiring with attached bake element back into their position behind the oven wall and attached the bars holding the bake element to the back of the oven wall. This is really easy because it is exactly like the on-line video, for I am a 75 year old female with little technical experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from LEXINGTON, MA
- Parts Used:
- WP74003019
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The bake oven element burned out
Removed two screws and disconnected the element. Reconnected the new element and reinstalled the screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETH from COUNCE, TN
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
burner receptacle failed (stove over 30 years old)
Took out burner (pulls out) Took out one screw that holds recep. in, cut the two old wires and attached new wires with wire nuts included in the new package.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from ELKTON, VA
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
My oven door seal had dried rotted
I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.
Was this instruction helpful to you?
Thank you for voting!