A3478XRW-N Admiral Range - Instructions

Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.

Overall, it was painless and easy with zero problems

The very old stovetop came with our house. It works fine but two of the four knobs broke recently. I never found the model number so I made my best guess based on the detailed descriptions on partsselect.com. I guessed right! My 13-year-old son did the install in just about a minute. The only thing I had to do was use a sharpie to blacken out some of the markings on the new knobs. The on and off lines didn't line up for my old stovetop. It was an easy fix and we're really happy.

Removed grates and bottom plate two screws holding it. Turn oven light on and unwire the wire. Unscrewed the two screws and replace. This took my husband about ten min. And for him he says that this was a walk in the park. He says if he can do it anyone can. This was one of the easy honey dews. Good luck with yours. Nola & keith

Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!

Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.

My brother is a handyman. The part was delivered very quickly. The instructions were very easy to read and after an hour, voila the oven works perfectly!

If your igniter glows but the burner doesn't light, your igniter is more than likely bad. It should have at least 3.2V to gas valve when the igniter is glowing in order to open the gas valve. The repair is very easy with only a 5/16" nut driver equired to remove and replace the igniter. It's pretty much a plug and play reair.

I can't believe how easy this was to fix! I amazingly found the part on-line at PartSelect website. I love that you pick part by size, color, etc. I didn't have a part or model number, so this made it super easy! I ordered the part and got it in the mail within 2 days....YEAH! I got my screwdriver out and attached the peice, slid the drawer back in and shazam! it was fixed! Thank you PartSelect and kudos to the person that set up the way you order your parts......awesome! Thanks!

1st unplug stove opened cover to wireing box with a phillips driver removed old part transfered wires one by one installed new part installed cover & pluged in stove & worked line new.

Piece of cake. Removed the Phillips screw with screwdriver, placed new one on the slide and used old screw to screw it in place. Drawer does not lean to one side anymore.

First I went online to find out about the availability of the part. In my search, I found what others had experienced and how they repaired it. Second, I ordered the part and followed others stories on their repair efforts. Third, I unplugged the range and removed the racks. Fourth, I removed the bottom of the oven which lifts out back first. Fifth, I removed the wing nut securing the flame difusser making it easier to access the element. Sixth, I had read that others had problems saving the original screws and/or threaded holes. I sprayed some wd-40 on both screws. They came out and back in without a hitch. Seventh, I removed and replaced the element, snap out, snap in. Eighth, I turned on the oven. It took about 15 seconds to glow but wow, it lit 5 seconds after that. I am my wife's hero!

I removed the back of the range to disconnect the wires to the igniter. Then I removed the two screws holding the igniter, screwed the new one in and reconnected the wires in back.
I was really pleased how easy it was to find the part on the website and how quickly the part came. The whole job was a snap. Thanks!

It took me 10 mins to replace the oven igniter and I did it myself. Oven is working fine now. I saved myself a $300.00 repair bill. Thank you for making the part available and saving me dollars!

I noticed that the ignitor would glow but the stove wouldn't light - I got the model number of the stove and googled the maytag model number. Came upon your website and realized that 94% of the time the problem was the amps were not enough to light the stove. I looked at all of the stories on how easy it was to fix. I ordered the part and received it within 3 days. I opened the door part way and lifted it straight up to remove it. I pulled out the bottom broiler plate by grabbing the back on pulling up. I undscrewed the wing nut of the flame bar and had easy access to the igniter. I removed the two nuts from the old igniter. Unplugged the igniter from the easy access door from the back and plugged in the new igniter. Replaced the access door and attached the igniter with the two nuts. Put the flame bar back on, put the broiler plate back on, put the door back on, plugged in the stove turned it on and success. It was so easy. I know in our area I would have paid near $200 for a service technician to come out and do what I did in approx. 20 Minutes and $50 for the part. Thank you so much for you website to help us not so talented appliance repair homeowners.