Models > CREA200ACW > Instructions

CREA200ACW Admiral Range - Instructions

Jump to:

All Instructions for the CREA200ACW
106 - 120 of 377
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Hudson from Cockeysville, MD
Parts Used:
WP74003019
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The element was completely gone.
Turned off power, removed 2 screws, un-hooked the connections, them put in the new element in reverse order.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lowell from Hardin, KY
Parts Used:
WPW10196405, WPW10196406
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Couldn't find correct drip bowls that fit.
Removed old drip bowls, removed burners installed new drip bowls,installed burners. They fit perfect and I received them two days after ordering.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carolyn S from white oak, NC
Parts Used:
WP74003019
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
bottom bake element broken and burned
First throw the breaker on the stove. Remove two screws in back of oven then slowly pull out loosen the wire attachements ......got new part in 2 days just as simple reverse the removal directions.,,,I am over 60 female and it was simple.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Herbert from Neenah, WI
Parts Used:
WP74003019
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The oven heating element burned out like a lit fuse!
Removed 2 phillips screws, unplugged 2 wires, threw away old element. Installation of the new element was just as easy but in reverse order. Piece of cake!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Susan from Grand Ledge, MI
Parts Used:
WP74003019
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
bake element disintegrated!
Seems every 5 years this bake element totally disintegrates, so we,re experienced! Pull the stove out and remove the back, remove the 2 screws that hold the element(now in 5 pieces), diconnect and discard. Place new element in and connect, replace the 2 screws holding the element in place. Replace stove back. Easy
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Yukon, OK
Parts Used:
WP74003019
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
snapped element
switch off the range. undo the two screws & unplug the two tabs. Replace with new element, connect two tabs, screw back in place. done!
recieved my replacement part the next day after ordering
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Betsy from Sun City, AZ
Parts Used:
WP74003019
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Previous element burnt up
I let my husband to the work...But it was very easy. I could have done it! He removed the screws, pulled the wires off previous element. Reattached the wires to the new element and screwed the ends back in place.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jackie from Hughes Springs, TX
Parts Used:
WPY04000035
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
burner would not heat.
I unpluged the old burner and pluged the new one in. Repair done in about 2 min,
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Raymond from Ottawa, OH
Parts Used:
WP74003019
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Element burned out.
First I removed the two screws that hold the element in place. I then pulled the element out aobut 3 inches and disconnected the wires.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Edward from Adamstown, MD
Parts Used:
WP74003019
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
No Bake, only Broil
POWER OFF! Unplugged oven from wall.

(Note: I found it easier to disconnect the wires from the element by removing the rear cover. Fumbling around inside the oven was getting me nowhere.)

Removed rear cover.
Disconnected old element.
Unscrewed the old element from inside the oven, removed, and installed the new element. Screwed the new element in place.
Reconnected wires in back, installed the back cover.
Connected power.
Tested. Good as new.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
robert from merrimack, NH
Parts Used:
WP74003019
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
oven didn't heat up
removed the old element by taking out two screws then removed the two wires. pulled out the old element , put the new one in . connected the wires and screwed it in. Done.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
PATSY from HALLWOOD, VA
Parts Used:
WP74003019
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Lower element out-oven wouldn't heat
I removed the two screws at the rear of the oven and pulled out the existing element, plugged in the new element, pushing it back in place and mounted the screws back in the bracket. I then made the "Tim the Tool Man" grunt noises feeling very proud that I am now officially a Handy Woman!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jonathan from Havertown, PA
Parts Used:
WP74003019
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Oven wouldn't heat
Easiest repair ever.

#1 - Turn off power (or you will get electricutued).
#2 - Unscrew back of heating elements
#3 - Disconnect wires (may need pliers)
#4 - Attach new heating element
#5 - Put in screws

Everything took 15 mintes max.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Jacksonville, FL
Parts Used:
WP74003019
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Bottom Element Burned out
Turned off all power to range.
Removed two Philip head screws
Gentle pulled unit Element forward
Removed two push on connectors
(Do not let wires fall back into oven holes)

Reversed the process.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Topsfield, MA
Parts Used:
WP74003019
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Oven quit in the middle of cooking the Christmas turkey. Fortunately we have a smaller oven on the top which finished the job. (a few hours late, but after a few cocktails and more visiting, it really worked out fine!)
I was blown away by how easy it was to order and receive this replacement part. I went on the web on Christmas afternoon, Googled "Magic Chef" and found your website. Your ordering process could not be easier (including the on-line drawings and all). I selected the lowest cost shipping method "3-5 days." Wednesday evening, I got your e-mail with the tracker. Thursday afternoon the part arrived! Saturday, we opened the oven, took out the old unit, and put in the new. It worked fine! Thanks again!!
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CREA200ACW
106 - 120 of 377