687AF-CKVW Admiral Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Audrey from Houston, TX
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would ignite sometime, sometime not. Always argued with the broiler when it was lit first.
My son removed the pan above the ignition switch, using only a screwdriver. He checked it against the excellent website photos for compatibility with what you had to offer. I order it and it was here in Houston within 2 days of the order. Took 20 minutes to remove and compare and 7 minutes to replace the old with the new. A piece of cake.
Best thing was that the oven/stove is 29 years old and I thought I would have to buy a new one (approximately $700 for comparable)and I am a Senior Citizen. So for $48.98 and lots of elbow grease to clean the stainless steel top etc. I have a dandy, operating, dependable piece of cooking equipment !!!!
Best thing was that the oven/stove is 29 years old and I thought I would have to buy a new one (approximately $700 for comparable)and I am a Senior Citizen. So for $48.98 and lots of elbow grease to clean the stainless steel top etc. I have a dandy, operating, dependable piece of cooking equipment !!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from HAMLIN, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
gas oven would not light
the igniter would glow but the gas would not flow...
i would have guessed the valve was bad, but every one else thought it was the igniter.. they were right. verry easy to install. the stove worjks like new.
i would have guessed the valve was bad, but every one else thought it was the igniter.. they were right. verry easy to install. the stove worjks like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Hacienda Heights, CA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
wall oven glowed but would not ignite
Un-did the old one put in the new. Iam 63 years old and a woman. Repair men wanted 500.00 plus to come out and repair I did it for cost of igniter in 15 min. Oven works great! Thanks parts select for making it so easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johan from Garden Grove, CA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
oven burner would not light.
The Just Answer website answer felt certain that the igniter was the problem, and hence I ordered a new igniter.
I removed the oven bottom plate and the cover over the valve connection to get an overview of the job. Was really not necessary. Actual repair was only to remove the two screws holding the igniter, pull the cord to get to the connector, and switch igniters. Then put everything back together again. Job done. Oven works great.
I removed the oven bottom plate and the cover over the valve connection to get an overview of the job. Was really not necessary. Actual repair was only to remove the two screws holding the igniter, pull the cord to get to the connector, and switch igniters. Then put everything back together again. Job done. Oven works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Redlands, CA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Our oven would not ignite
We replaced Flat Style Oven Igniter simply by removing the oven racks, then removed the bottom of the oven. Used a Philips screwdriver to remove the old igniter, placed new one in. The wires to the oven from the ingniter just needed to be in a clip. Tightened the screws and replaced bottom & racks. Oven worked wonderful after this, like a brand new oven!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Ada, MI
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb went out in my oven
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from Girdwood, AK
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
very slow heating, smell of gas
Unpluged then stove, turned of the gas.Unpluged the igniter from the harness, unscrewed the igniter and pulled it out through the front of the stove.Installed in reversed order.Stove works like new. The part got to Alaska in 2 days. Thank you for your service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Farmington Hills, MI
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven would not work, broiler and range did work.
Came to this website to look for possible cause. The major fault for my problem was the igniter @ 61% of the time. So, I ordered this part @ about $55. Opened the range floor, removed two nut screws and old igniter, by unpluging. Plugged in new part reattached screws and tested before putting it back together. Worked fine, without snags. However I did pull up and remove oven door for complete access to oven.
Rick,
Detroit, MI.
Rick,
Detroit, MI.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mitch from brooklyn park, MN
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven didnt light
i removed old part, then installed new one. easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from St. Remy, NY
- Parts Used:
- 1430322
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burners would not light sometimes
Slide stove out unplug remove cover on back bottom left 3 screws remove wires from old module and plug into new module could not remove old module I glued new to old replaced cover pluged back in slide stove back in and the burners lit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Belleville, IL
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Things cooked in the oven were taking longer than usual to be done.
Using a remote digital thermometer, noted that the oven temp reached operating temp, then fell 40-50 degrees, was slow to recover. After reading entries from others on your web site, removed oven floor and watched the burner operation. The igniter would light the gas at first, the temp would go up, gas would shut off. Then when the igniter came on again, it would glow for a long time before gas would come on.The replacement was very simple, even though one of the mounting screws twisted off, the remaining screw seems to be holding.Was a simple unplug old connector, insert new connector. The optional parts included in the kit were not needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joan from florissant, MO
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not light
My brother-in-law did the repair as I am a scardy-cat and didn't want to tackle it myself. The most difficult part of the repair was the awkward position you have to get your body in to do the repair. Other than that it was a piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Greenwood, AR
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven would not light, but igniter would glow.
Removed Old Igniter and installed new one, parts and connector fit fine, no modifications needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIKE from Phelan, CA
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven quit lighting
I removed the old igniter, held in place with two screws, pulled the wiring out to get to the clip, and undid the clip. Clipped the new igniter to the wires, pushed back into the hole at the back of the oven, installed the igniter with the two screws, and fires just like new! I had a loose wire on the old igniter and hassled with that for years because I didn't realize how easy the fix was.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HELMUT from MIDDLE VILLAGE, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The oven would not light even though the glow plug lit.
Remove the shelves and floor of upper oven and remove the two screws holding the glow plug. Disconnect wiring harness and replace with new one. Screw new glow plug and replace floor and shelves.
The oven worked like a charm again.
The oven worked like a charm again.
Was this instruction helpful to you?
Thank you for voting!