LGR3330ADW Admiral Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from VALLEJO, CA
- Parts Used:
- WPW10162384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Gasket was worn out.
Put a new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from MONTAGUE, MI
- Parts Used:
- 12002358
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bottom trim section was rusting
To better access the bottom screws, I removed the door by opening it to the first open position and lifting it up off the hinges. No tools are needed for this but careful, the door IS heavy! Place on table or counter top. Remove the Phillips screws, old trim, and clean the outside of door. Position new trim and replace with the new screws provided. By securing the new trim, I did not have to worry about the glass sliding out when flipping the door to clean the inside. Finish by sliding the door back on the hinges. Looks like brand new!
Side Notes: One of the side pieces of the trim was fairly bent when received. Since the misshapen piece was nicely painted i.e. parted when bent, this was a Maytag (Whirlpool) supplier issue and NOT a PartSelect issue. Rather then damaging the paint bending this piece back to fit the door, I reused the old side piece which was in great shape.
Thanks PartSelect , you're the best!
Side Notes: One of the side pieces of the trim was fairly bent when received. Since the misshapen piece was nicely painted i.e. parted when bent, this was a Maytag (Whirlpool) supplier issue and NOT a PartSelect issue. Rather then damaging the paint bending this piece back to fit the door, I reused the old side piece which was in great shape.
Thanks PartSelect , you're the best!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KATHY from PLEASANT GAP, PA
- Parts Used:
- 12001655
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not maintain temperature
So simple! I really had no idea what the problem was. I found the PartsSelect site, read the comments from fellow Maytag double oven owners, diagnosed the problem as the sensor and ordered the part. It arrived in only two days! We removed the back of the stove, pulled the old sensor through, plugged the new one in and YAY the oven is like new. I have to admit most of the repair time involved sweeping up the dog hair that had accumulated under the stove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marty from Kennesaw, GA
- Parts Used:
- 74004053
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Replaced igniter in right rear burner
Simply remove the box containing the two right burners. Access the igniter by removing about 8 screws and pull the coupler for the igniter off with a pair of needel nose pliers. Replace with new igniter using the same tool. Re-assemble the box by screwing in the screws and give it a try. Worked great. Once slight hitch, be sure you don't leave a second screw driving in the box. As it will raddle. So I had to remove and reassemble twice. I'm not a surgeon! Thanks for the fast delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Abingdon, VA
- Parts Used:
- 74003645
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Inner glass pane broke during self-cleaning operation
I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM J from JERSEY CITY, NJ
- Parts Used:
- 12001655
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Just unscred the 2 screw on the Thermometer
Unplugged the stove and unscrew the 2 screws on the thermometer inside the stove and unplugged the white plastic in the back of the stove and I had to put the new extra piece that came with the sensor kit as it was needed because the socket were different.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Chapell Hill, NC
- Parts Used:
- WPW10162384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven heat loss, door gasket needed replacement
The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in place! Simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Portsmouth, NH
- Parts Used:
- 12001655
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven would not come to set heat
slide out stove remove rear cover (6 screws) to access sensor plug . remove two screws from inside oven area and remove part,replace in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Reno, NV
- Parts Used:
- 74003387
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
old bulb fused into old socket.
removed old socket and replaced.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Omaha, NE
- Parts Used:
- WP74011141
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The Hinge Was Broken
We moved into a house with seemingly newer looking appliances. After the dishwasher broke and destroyed our floor, we found out that they were all twelve years old. Amazing the condition they were in after all that time.
The oven was the next thing to break. The hinge snapped, and while we could still use the oven, it allowed hot air to seep out.
So I checked online and lo and behold, I found a hinge for under $20. Wow. Much cheaper than a new range.
The most amazing thing was that I purchased it on a Friday afternoon, and it showed up on Saturday, so we could do the repair over the weekend. I cannot tell you how impressed I am with that kind of service.
We had to take off the side panel which was a pain, but all in all, it was 7-8 screws and swapping the hinge was easy. One of the screws did not want to go back in, so I had to find a replacement, but other than that, it was a pretty easy repair.
Thanks!
The oven was the next thing to break. The hinge snapped, and while we could still use the oven, it allowed hot air to seep out.
So I checked online and lo and behold, I found a hinge for under $20. Wow. Much cheaper than a new range.
The most amazing thing was that I purchased it on a Friday afternoon, and it showed up on Saturday, so we could do the repair over the weekend. I cannot tell you how impressed I am with that kind of service.
We had to take off the side panel which was a pain, but all in all, it was 7-8 screws and swapping the hinge was easy. One of the screws did not want to go back in, so I had to find a replacement, but other than that, it was a pretty easy repair.
Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francis from delavan, WI
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven does not heat but broiler works
Oven and broiler have two seperate igniters. Broiler worked but oven did not heat. Oven igniter located under metal pan at base of inside of oven. remove pan by lifting, and remove completely from oven. Igniter under this pan and held in place by two srews. Remove screws, unplug from cable, replug in ne igniter, replace two srcews and pan, and you're done! this part cost about $50 and I installed, last time Sear replaced =$300.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from East Sandwich, MA
- Parts Used:
- 74003645
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Shattered inside glass when attempted to self-clean
Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Monroe, NY
- Parts Used:
- WP5504M003-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
floor panel heavily stained and warped
slide latches in rear of floor panel forward and remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from ALEXANDRIA, LA
- Parts Used:
- WP3807F708-71
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old glass support rusty in one spot.
I took the door off and removed five phillip screws from the old bottom support and removed it. I took the opportunity to clean the glass on the front and back before placing it back on. It simply fits into two keepers at top and is held on by the new support at the bottom. I replaced the five screws and put the door back on. It is a simple job that only takes a few minutes.
Was this instruction helpful to you?
Thank you for voting!