A31703SAAL Admiral Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ernest from CINCINNATI, OH
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The oven igniter would glow red but gas did not come on to light the burner.
I watched a repair video, unplugged the electric,turned off the gas valve and disconnected the gas line. removed the shelves and burner tray. removed 2 screws and unplugged the igniter. Replaced the igniter and put tray and racks in.Hooked up gas and plugged in the electrical plug. Job done....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from AURORA, MN
- Parts Used:
- 12400035
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
No heat in oven
Checked igniter it glowed but never got hot enough to open gas valve. I switched igniter from broiler to oven and oven burner lit. Switched igniter back to broiler as wires were shorter than the oven igniter. Ordered part from number and picture comparison. It took about 20 minutes to get it installed and all stove parts back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANCES from AFFTON, MO
- Parts Used:
- W11400301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
35 year old range. grates too dirty to clean. Parts Select had exact replacement grates. Perfect fit.
Easy, removed from box, put in place on range. Happy customer. Good company to find exact replacement parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matt from Arlington, AL
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Oven was slow to get to temp and not holding temp
Thanks to previous posters, this seemed to be an igniter issue, and I found the idea of swapping the broiler igniter for the bottom one particularly good - I knew exactly what part was broken and how easy/hard the job would be prior to ordering. The part used snap in electric components, so the only work was in removing and re-installing the parts. Working in the oven was by FAR the most difficult part of the entire process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tara from ALBANY, NY
- Parts Used:
- WP5504M003-19
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
The oven bottom was warped and could not be positioned properly in the oven.
Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mz from COLUMBIA, ME
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.
Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gino from ARLETA, CA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
igniter failed to ignite
Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from BROWNVILLE, NY
- Parts Used:
- W11665456
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
My original back leg broke because the floor is uneven. Had to pull it out several times.
Put the back of stove on blocks of wood to get high enough to screw the new leg in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacob from LITTLE CANADA, MN
- Parts Used:
- W11400301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Simply remove and install new parts
Overall, it was painless and easy with zero problems
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Santa Maria, CA
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
gas burner on stove top not lighting ,other 3 work fine.
Make sure all burners on stove top are off.Half twist burner top to separate burner from stove top.The burner slide fits over the metal tube that transports the gas to the burner.Remove the 2 slip fit connected wires from the underside of the burner.They should be of different sizes so no worries about incorrectly re-attaching them.The igniter has 2 philips screws holding the igniter to the burner, Remove those and the igniter will be able to be removed with a little wiggling.Insert new igniter thru the hole in the burner and secure with the 2 screws. Reattach wires , place burner back on top making sure the wires aren't being crimped when the burner slides over the aforementioned metal tube and twist burner to seat in stove top, turn on burner to confirm igniter now ignites properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from ELKTON, VA
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
My oven door seal had dried rotted
I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nola from Enid, OK
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stove Would Not Light To Heat Up.
Removed grates and bottom plate two screws holding it. Turn oven light on and unwire the wire. Unscrewed the two screws and replace. This took my husband about ten min. And for him he says that this was a walk in the park. He says if he can do it anyone can. This was one of the easy honey dews. Good luck with yours. Nola & keith
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Spotswood, NJ
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven would not heat up fully, smelled of gas.
Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dominick from CLARKS SUMMIT, PA
- Parts Used:
- 12400035
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Oven would not ignite
Very easy, video helped tremendously
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from Newton, IL
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven ignitor would glow but took 30 - 40 mins to heat
It took me 10 mins to replace the oven igniter and I did it myself. Oven is working fine now. I saved myself a $300.00 repair bill. Thank you for making the part available and saving me dollars!
Was this instruction helpful to you?
Thank you for voting!