687WM-TKSAW Admiral Range - Instructions

My husband simply twisted out the old burner with a pliers and attach the new burner. Simple and easy....

Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.

Turned burner about 1/16 turn to left. Lifted burner from stove. Disconnected two wire connectors. Connected same wires to new burner. Set burner in place and turned 1/16 turn to right. Tested burner. Lighter worked on first attempt and burned perfectly. Took about 3 1/2 minutes.

Overall, it was painless and easy with zero problems

My brother is a handyman. The part was delivered very quickly. The instructions were very easy to read and after an hour, voila the oven works perfectly!

Remove oven door, remove burner bar, replace ignitor, splice wires together because the old electrical connectors had melted together. Shipping was fast and extra wire, insulation and ceramic wire nuts were included.

I watched a repair video, unplugged the electric,turned off the gas valve and disconnected the gas line. removed the shelves and burner tray. removed 2 screws and unplugged the igniter. Replaced the igniter and put tray and racks in.Hooked up gas and plugged in the electrical plug. Job done....

Checked igniter it glowed but never got hot enough to open gas valve. I switched igniter from broiler to oven and oven burner lit. Switched igniter back to broiler as wires were shorter than the oven igniter. Ordered part from number and picture comparison. It took about 20 minutes to get it installed and all stove parts back together.

Super easy. Turn off gas and unplug. Lift door off hinges, just pull up on it. Take racks out. Lift floor of oven out. You may need to release clips in the back of the oven, but mine were not engaged. Remove wing nut from shield plate and lift plate off. Using nutcracker, or Phillips screwdriver, remove screws holding the igniter to the brace plate. Carefully pull wires from the back of the oven wall. Carefully unplug the old part. Carefully plug in the new part. Feed wires back into the oven wall and install fiberglass padding. Replace screws, shield plate, wing nut, oven floor, oven racks and door. Door just slides back onto hinges. Watch the video on parts elect. Couldn't have been easier. Saved $500 on replacing my oven. $40 for DIY repair. Awesome!!!

Thanks to previous posters, this seemed to be an igniter issue, and I found the idea of swapping the broiler igniter for the bottom one particularly good - I knew exactly what part was broken and how easy/hard the job would be prior to ordering. The part used snap in electric components, so the only work was in removing and re-installing the parts. Working in the oven was by FAR the most difficult part of the entire process.

I removed the old module ,replaced new bracket,crimped new wire lugs on wires. being an electrician for 50 plus years helped.      Thanks   Lloyd

ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.

took out two screws that held Igniter to burner, unbluged wires from behind and pulled them out to the front of over, replaced with new one, solved the problem of the burner not coming on,,,,

removed oven floor, removed two screws in element . pulled out element wires, secured them so they would not fall back into slot, snaped in new element . scewed it in place , replaced floor . thanks partselect.com

We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No appliance store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!