687AM-TKSAW Admiral Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ramiro from Bernalillo, NM
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Replaced burner
Went well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Can Francisco, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
corroded burners
Unscrew the burners an install new ones! Anyone could do this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- javier from Santa Ana, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bad Gasket
I just twist the burner, pulled it out, disconect the two wires. Reconect the wires to the new burner and placed back .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Staten Island, NY
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original burner was eroded on the bottom and flame was coming from undernealth the burner
Very easy. I disconnected the original burner with one turn as well as the two wire connections for the electronic igniter. I then connected the wires to the same positions on the new burner and placed the new burner in place with one half turn to match the indented openings to secure the burner tightly in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Flemington, NJ
- Parts Used:
- 7201P015-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
lamp retainer gasket disintegrated when changed burned out bulb
I just removed the lamp retainer plate and glass cover, inserted the new gasket, and screwed everything back in place. Simple as that. I was enormously pleased that the part arrived so quickly -- just in time for me to cook my Thanksgiving turkey and use the self-cleaning feature.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- eric from winter haven, FL
- Parts Used:
- 12001596
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
no spark on top burners
part was by the brolier drawer inside under stove removed 2 screws on cover/ part was attached to cover removed module line 1-2 fit/ had to use supplied disconects crimped on 4 burner wire leads/taped around module w/ elec. tape put back 2 screws finished. works now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gino from ARLETA, CA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
igniter failed to ignite
Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcia from Bronx, NY
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
cap on the burner broke off
My husband simply twisted out the old burner with a pliers and attach the new burner. Simple and easy....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from LORENA, TX
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burner worn out
Turned burner about 1/16 turn to left. Lifted burner from stove. Disconnected two wire connectors. Connected same wires to new burner. Set burner in place and turned 1/16 turn to right. Tested burner. Lighter worked on first attempt and burned perfectly. Took about 3 1/2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Syracuse, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Oven would not start, ignitor was not doing anything
My wife said the oven would not heat up, I took a look at it and determined it was not igniting. I figured there was an electric spark like my BBQ. When I took the pan out of the bottom of the oven I saw that it did not look like anything I had seen before. I looked it up online and found out it had a glow ignitor that just heats up and then ignites the gas. Mine wasn't doing anything so I removed it, got a part number off of it an plugged that into this site. It came up with the part, i ordered it, put it in and started it up. probably took about 45 minutes total including taking it out and then replacing it. Really easy and the oven is now working fine. Figured it would have been a couple hundred dollars to have someone come to the house and fix it, I did it myself for less than 50. Thanks Partselect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from SAN JOSE, CA
- Parts Used:
- 7733P099-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replacing broken stovetop knobs
The very old stovetop came with our house. It works fine but two of the four knobs broke recently. I never found the model number so I made my best guess based on the detailed descriptions on partsselect.com. I guessed right! My 13-year-old son did the install in just about a minute. The only thing I had to do was use a sharpie to blacken out some of the markings on the new knobs. The on and off lines didn't line up for my old stovetop. It was an easy fix and we're really happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacob from LITTLE CANADA, MN
- Parts Used:
- W11400301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Simply remove and install new parts
Overall, it was painless and easy with zero problems
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Spotswood, NJ
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven would not heat up fully, smelled of gas.
Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from West Winfield, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven would not light reliably.
Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONNIE from SAG HARBOR, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Igniter for oven not working
Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!
Was this instruction helpful to you?
Thank you for voting!