A3637XRW Admiral Range - Instructions

Unplugged stove. Removed door. Unfastened 2 screws at rear of oven. Removed wires from bake element. Connected new bake element. Replaced screws and door. Plugged oven back in.

Pretty simple, except the element melted very close to one end, so the screw holding the element to the rear of the stove was partly melted also. Had to drill it out & used a nut & bolt to secure the new element.
Apart from that, it was a breeze. As others have done, I re-tightened the lugs that the element plugged into.
Suggest a "test heating" before using stove: mine had a strong odor on first use, fine afterwards

Turned off the breaker to the stove. Removed the screws holding the old parts in and unplugged the element. After reshaping the element because it got damaged in shipping I plugged the wires to the new element, replaced the screws and turned the breaker back on. Tried the stove and it has worked fine since.

Remove the bottom rack from the oven. Pull the heating element straight back and out of the oven. Inserted the replacement burner in the opposite manner. Part was delivered in a timely manner.

Removed back of stove (6 screws), puled clips loose. Two screws inside oven, pulled out old element. slid new one in, replaced screws, slid on clips replaced back panel. Don't forget to unplug the stove frist.

Took out 2 screws pulled off the 2 female connectors. put the conectors on the new element and put the screws in. It took less than 10 minutes

This was a snap. It took me longer to find the right part number than it did to make the repair. After securing power to the oven, I removed the racks. I then unscrewed the element supports and pulled the element out slightly to expose the connectors. Using a pliers I removed the connector from each side of the element. At this point, I should have placed a piece of electrical tape to prevent the connector leads from slipping back into the body of the oven. Instead, I fished them out with a tweezer, and slid the connectors back onto each side of the element. I then screwed in the elements supports, replaced the oven racks, and restored the power. It literally took less than 10 minutes.

Super simple. My husband ordered the part. It arrived in 3 days. The old element plugs right into cables on both sides of the back of the oven and are secured to the rear wall with screws. I unscrewed the plates, detached the wires on each side and slid the new ones in place. It was that easy and took me about 10 minutes.

. First I removed the two screws that hold the ace. I thenelement in place. I then pulled the element out about inches and disconnected the two wires...)

I unplugged the oven, sat the flash light in the oven and removed the two screws that hold the element in place. I pulled the element out and diconnected the two metal wire clasps from the element. Connected the new element, made sure the clasps were secured. Slid the wires back in and replaced the screws. Tested the oven, it heats up to correct temperature. I am a women and it was real easy thanks to the other repair stories I read.

Removed old element (two screws) unclipped two wires. Clipped the two wires to the new element (one at each end), reinserted new element, replaced the two screws. Done. Oh, flipped the circuit breaker back on:-)

unscrewed the old baking element, took the yellow wire off, and put the yellow wire onto the new baking element and screwed it back onto the oven. Took less than 15 minutes.

Two screws out, the old bake element came out easily, was able to disconnect very easily from the clip wiring, then replaced with new. I even was able to replace the oven light bulb at the same time. A real cinch.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, at that point I attempted to reconnect the two wires, that is when I found out why they tell you to unplug the electricity. It wasn't a big shock, more of a consistant shock. Once I unpluged the stove from the wall, it only took about 3 minutes or so to connect the wires and replace the two screws. I have no doubt I saved a hundred dollars doing this myself.
Thank you for your prompt delivery on the replacement part for my Bake Element at what I felt was a very reasonable price.