Models > KV25G0XBM5 > Instructions

KV25G0XBM5 Whirlpool Range Hood - Instructions

Jump to:

All Instructions for the KV25G0XBM5

Customer:: Herbert from Glendale, AZ
Parts Used:: WPW10170080, 8212396
Difficulty Level:: A Bit Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

The mixer sounded like the gearbox was full of gravel.

The transmission housing was cracked and one of the bearings was broken. I replaced both of them, but the mixer really didn't sound any better. So I replaced the gears in the transmission, and while that was better it still wasn't correct. I am going to replace the other bearing and the planetary shaft and see it that aligns everything a bit better. I believe the problem is the way the gear on the end of the motor shaft is working with the worm gear, the bearings are not keeping the correct spacing. Hopefully, the new one in the rear will fix the problem.

Was this instruction helpful to you?

Customer:: Leonard H. from Rustburg, VA
Parts Used:: WP9709511, W11192795, W11192795
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers

bevel gear chewed up by the hub bevel gear

took mixer apart down to removal of gear case cover.upon removal of this cover found the bevel gear and hub bevel gear chewed up .removed them both then replaced them both.and also had to solve a clearence problem between the 2 gears they were too loosely meshing. so had to push the hub retainer closer to take up the meshing slack.not sure my repair will hold but i have another set of gears and another solution that will surely fix it.

Was this instruction helpful to you?

Customer:: Brett from Yosemite, CA
Parts Used:: W11192795
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers

Stand mixer gear teeth sheered off

First and foremost, I am not mechanical at all. I typically refer to parts as thing-a-ma-jigs, and whatca-ma-call-its. When it froze up and started to make a loud grinding noise, I guessed it was a gear problem. I decided to try to take it apart, What did I have to lose? If I couldn't figure it out, I would be down a mixer. I was already down one as it was. It was very easy to take apart and I could immediately see what gears needed to be replaced. Parts Select made it very easy to see what parts I needed. And delivery was lightning fast; the next day after it shipped! I found a PDF on line on how to dis-assemble and re-assemble the mixer. I got it together and it mixed for a few minutes and froze again. I took it apart and realized that I didn't have the whatcha-ma-call-it (worm gear) seated properly. Fixed it and put it back together and put it to the test. Working just fine now! Thank you Parts Select for making this very easy!

Was this instruction helpful to you?

Customer:: vicki from topeka, KS
Parts Used:: W11123171
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

part broke

Husband easily put back together and it works great.

Was this instruction helpful to you?

Customer:: Linda from Lynden, WA
Parts Used:: WP9709194
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Thumb screw

the plastic covering the thumb screw cracked almost half way and lost the piece....so the new one is being used to replace this old one...very easy to install

Was this instruction helpful to you?

Customer:: marjorie from juda, WI
Parts Used:: WP9709194
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

head of screw was broken in half

I looked on line found the product sent in information and 3 days later was in my mailbox,great service and ease of ordering. thanks marjorie

Was this instruction helpful to you?

Customer:: Dennis from Frankfort, IN
Parts Used:: W11086780
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

Worn worm gear

The KitchenAid is "old school" in that it is held together with simple (but very stout) bolts and screws. I removed about 10 such fasteners, slipped off the gear retainer, and pulled it out. On Sunday, a very nice customer service rep helped me order the right part, but I did the rest on line in a matter of seconds. It shipped on Monday and arrived on Wednesday. Took about 10 minutes to put everything back. I REALLY WISH everything was this easy in 2012!!!

Was this instruction helpful to you?

Customer:: Dawn L from Ceres, NY
Parts Used:: WP9706648, WP9706648
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Trouble with switch

removed top casing, removed old switch and sensor,and replaced with new ones. It was just a matter of a half dozen screws and unpluging 4 or 5 wires and then reversing the process. Couldn't be easier. thank you

Was this instruction helpful to you?

Customer:: JOHN from RIVERSIDE, CA
Parts Used:: WP9706648
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Mixer goes full speed even when on low setting.

Removed one screw to remove deco band around mixer body. Removed four screws under band to remove mixer top. Removed two screws holding switch. Removed wires one at a time putting them in the same position on the new switch. Re-attached switch, mixer top, and deco band. Works perfectly.

Was this instruction helpful to you?

Customer:: brian from saint simons island, GA
Parts Used:: WP9706648
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

speed controll switch. would start and stop on its own.

replaced Speed control board. less than 40.00 took ten minuets from the time I started until we were making cookies.

Was this instruction helpful to you?

Customer:: Karen from Salem, IL
Parts Used:: WP9709194
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

The thumb screw plastic came off

Open the package with the new screw and it looked like the screw was wider. I tried it to see if it goes in and as long as you screw it straight in, there was no problem.

Was this instruction helpful to you?

Customer:: Jane from Crivitz, WI
Parts Used:: WP9709194
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

I had lost the thumb screw

I sent for a new thumb screw and screwed it in where it belongs and now I can use my other attachments.

Was this instruction helpful to you?

Customer:: PJ from Rome, GA
Parts Used:: WP9709194
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Broken Part to KitchenAid Mixer

Great experience. Reasonable cost. Quick delivery. Would certainly use PartSelect again

Was this instruction helpful to you?

Customer:: robert from wilton, CA
Parts Used:: W11086780
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

didn't turn

ordered the part and put in in with the help from the instant repairman

Was this instruction helpful to you?

Customer:: Rodney from Thornton, NH
Parts Used:: W11086780
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

worn gear causing slippage under load

removed cover. Removed cover over gears. Used lock washer pliers to remove lock washer. Took out gears. Cleaned metal shavings from old gear and grease. Reassembled using new gear. Took about 15 minutes and saved $$ over sending mixer out for the repair.

Was this instruction helpful to you?

All Instructions for the KV25G0XBM5