R200 - Instructions

pulled old one out , cleaned the area & replaced with the new one.

Removed the old grease screen and cleaned the entire area thoroughly and replaced the screen

Used a screw driver with a socket head to remove the two hex head screws holding the old element. Pulled the old element forward until the two wire attachements were visable. The wires were attached with a simple tab connector. Removed the wires from the element. Attached wires to new element slide the element and wires back into wall of oven and replaced screws. Done!

Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.

I had put up with a filter that got more and more raggedy every year, but I thought my 30 yr. old range/grill top was too old for me to find an replacement filter. What a great service you offer. I found you by web-surfing, typed in the model #, and presto--you sent me the shiny new filter. All I had to do was pop it in and throw away the nasty grill (after washing the scent off to keep the bears out of my Colorado garbage.) Thank you!

Cleaned out the downdraft cove, inserted the new filter, and put old filter in garbage can. Laughing. Thanks. Wish you had a FAQ's hotline. I'd like to know if the radiant inserts fit the older coil-type models.

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

Locate and open appropriate breaker to kill power to the range. (very important if you intend to see tomorrow).

Pull off the control knob.

Remove 2 screws that hold in control pannel.

Lift out the control pannel to the extent that the wires will let you. (2-3 inches)

Remove the nut that holds the switch/controller in the pannel.

Remove the wires one at a time and reconnect them to the new switch. Make sure to connect them the same way on the new switch.

Re-install the switch in the pannel.

Re-install the pannel in the stove.

Close breaker and test burner contol.

Removed the two screws that hold the element in place at the rear of the oven.Unplug each prob,you may need pliers as they can be a little tight.Reconnected the new element.Keep the old screws.New element does not come with screws.Always unplug range when doing repairs.

The first task was to find the rings, drip bowls and elements on the "PartSelect" webpage. It was surprising easy, especially since I have no experience whatsoever in replacing range parts. The ordering was straight-forward, and most of the parts arrived within a week, a couple were back-ordered, but arrived a week later. Instillation was easy - just unplug elements, lift parts out, and insert new parts. I made a mistake in ordering - for the left side of the range, no adaptor rings are needed. I returned these excess parts to PartSelect, and within a week, they refunded the costs of these parts. Overall, I'm very please with the parts and service.

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

The drip pans, burner knobs and electric surface elements are easily removed and replaced. The new receptacles for the burners were NOT easy to replace, but electricians were on hand to install when they replaced the cook top into the new counter top. Even the electricians had to read the instructions - and remove the control panel to replace one of the receptables. Looks like a new cook top.

Pulled the motor and blower wheel from below. Replaced both. I think it was easier to replace the two together than just the motor.I also had old light indicators so we replaced them since the stove was sort of apart. The repair was not difficult at all, and my 30+ stove top looks and runs great!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Replaced the element and put back in place. Took about 10 minutes. Repair part came in 2 days. Very awesome website!

Took the old knobs off and replaced them with the new!