MMV4184AAB - Instructions

After reading on-line about other Amana microwaves, that said the arching was probablly due to dirt or grease & I knew it wasn't dirty, I decided to try the sandpaper recommended to clean the carbon from the wall where the shelf holder had burned several years ago. This caused the remainder of the clip to become loose. I then took a sharp knife & popped the clip out which left a neat square hole which your shelf holder popped right into. The filters were an afterthought because I didn't want to pay shipping for only a $2 item

Since others reported similar problems and it was just the fuse we tried that first. That wasn't the problem so we ordered the Door Interlock Switch Kit. Shipping was very fast! Our microwave had 3 switches. My husband asked how to know which one to switch. I read that one person just did process of elimination. Luckily ours worked on the first change out! So happy to have stumbled across this site and not have to buy a whole new microwave.

I started by calling a reputable service company to diagnose my problem. The repair tech told me it was the magnetron and it was a "very difficult" repair that required two people because the over-the-range unit needed to be taken down. I asked for a detailed estimate. He quoted $550 including parts and labor. After he left, I researched the part costs on this site and realized his costs were very inflated. I purchased the magnetron for $220. It arrived at my door two days later. Installation was very easy. First, I unplugged the unit. Then, while my wife was making sure it did not fall off the wall bracket, I unscrewed the two mounting screws from the top of the cabinet. I lifted the unit down from the wall and set it on the kitchen counter. The shell needed removed from the microwave which involved about 20 screws. This provided access to the magnetron on top. The magnetron is secured by five screws and a plug. I unplugged it, unscrewed it, and removed the old part. Then, I installed the new magnetron, and tested the microwave to make sure this did the trick. It worked. I put the outer shell back on the microwave and cleaned the microwave. (This is a great opportunity to clean the areas you do not typically see!). I then remounted the unit and plugged it back in. Saved myself a bit of money so I took the family out to dinner and a movie to celebrate. Microwave was in working order for heating up left overs the next day! Thank you!!!

removed old cover to lamp and reinstalled the new one by unscrewing one screw and screwing the new one back in

Lifted up the glass plate and stuck the assembly under it ;)

I unscrewed the light cover, removed the burned out light bulb and replaced it with one I ordered on Partselect.com. It was very easy.

I didn't do the repair -- my husband did, said it was easy, had no problems what so ever! The new bulbs give a lot more light to the cooking area.

remove 4 screws from top, front louvered panel snaps out. remove 1 screw from top of keypad, keypad pivot's forward and can be removed. There is a white mounting bracket inside left. Remove two screws, one top and one bottom, bracket lifts up and out. 3 sets wires are attached, mark them with masking tape, top, center, bottom and pull out plugs. They can only attach one way. Using a very small screw tip, lift plastic latch from switch, it rotates out and is removed from the pivot pin. reassemble in reverse order after switches are replaced

I put in the filter. The "over the stove microwave" made installation so easy even a woman could do it!

It literally took me longer to unpackage the fuse than to install it. I removed the outer shell by unscrewing the five screws, lifted it off and set it aside. The old fuse was readily visible so I pulled it out and put the new one in its place. I set the shell back on and replaced the screws. I plugged it in and ran it for 30 seconds while still in the shop just to make sure that solved the problem and presto - it worked like a charm. A $20 part saved me from having to purchase a new microwave (sadly, I had to break the news to the wife).

Replaced light bulb.

You had alerted that it was imperative to unplug unit before starting to remove defective bulb. As described, there was silicon on bulb and socket and bulb broke upon my attempt to remove. Had to use needle nose pliers to get metal base of old bulb from socket, then all went well.

First let me say that I tried several places to get what I thought was a simple light bulb. This included several national hardware stores as well as a national electrical supply company. No luck. Went to the manual and PartSelect. Not only did you have it in stock, ship right away,at a reasonable price it arrived in a matter of days. One would not normally think of receiving a "how to" video to change a light bulb but you did. That impressed me. Suffice to say the replacement went well and you can be certain the next time I need a part I will go to you first. I am also impressed with the organizations with which you are affiliated with. BBB, Norton, PayPal, money back guarantee etc. Thank You The entire process was made pleasant with your support.

Replaced with new covers.

Removed the glass cover and replaced the bulb. Very simple.