KV25G0XAQ6 Whirlpool Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Needed repair
The worm gear was defective. Called the 888 number and received excellent service. Said I would receive a refund and a new one in the mail.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from WORTH, IL
- Parts Used:
- WPW10170081, WPW10170080, WP9709231, W11086780
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
noise in trans.
took it apart. more grease all over. Put in all but one gear on the top. The noise is still there going to try to but the old bearings in and try again. I went back to the old worm gear and allmost all the noise stopped. I did put the new bearings in and the other gears. It seems that the gear on the worm gear was cut wrong. The noise was tear able. I tried the different parts I ordered one at a time. To find out which one stopped the noise. Every time I took a part I had grease all over. It took so long every time I put in a new part to put the trans back together again. I had grease all over.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from Gilbertsville, PA
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing thumb screw on my kitchen aide mixer
Dear Customer Service,
I just would like to express my gratitude for your wonderful service. I received my part for my Kitchen aide mixer on time as promised. The part fit perfectly. Thanks you PartSelect for being there.
What a Great Site!
A Happy Customer!
I just would like to express my gratitude for your wonderful service. I received my part for my Kitchen aide mixer on time as promised. The part fit perfectly. Thanks you PartSelect for being there.
What a Great Site!
A Happy Customer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Hiawassee, GA
- Parts Used:
- 8212396, WP67500-55
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the old housing was plastic and was broken
the repair was very simple, total time probably 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Turtle Lake, WI
- Parts Used:
- W11192795
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Gears had stripped due to housing crack and movement
Took top apart and installed new housing and two gears. Reassembled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHRISTINA from NEW GLOUCESTER, ME
- Parts Used:
- 8212396
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Plastic gear cover broken
Removed plastic cover, removed grease and put in new mixer and put new cover back on.
Was this instruction helpful to you?
Thank you for voting!
Grinding sound
Replaced cracked plastic gearcase/transmission with new medal one and replaced hub bevel gear attachment, bevel gear and gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ethel from Crystal River, FL
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
thumb screw broke
it just screw in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tina from La Farge, WI
- Parts Used:
- WP240185
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Pin-bowl lost
Simply placed it in the slot and pounded until firmly in with a soft mallet. Thanks to your site I was able to find the piece easily and very inexpensively. Thank you so much. I would die if I couldn't fix this machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bedalia from Rialto, CA
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Replacement of digital window in oven unit
I did not do the repair myself, however, I contacted a suggested service company which in turn was a company I had used before when I had problems with my JenAir microwave. Excellent service, prompt and very professional. Thank you JenAir for your assistance in providing promptly the parts needed to complete this job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jose from denver, CO
- Parts Used:
- W11192795
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
attachment driver will not work
Remove screw at back of mixer,remove metal sleve and remove three more screws (front and sides. remove screws and plastic cap of gear box then remove holding ring in post and remove damaged ring installation is opposed of removal.
Was this instruction helpful to you?
Thank you for voting!
Gears ground when roller attachment applied.
Took screw off band. This revealed 4 screws to upper housing. Removed 4 screws and lifted upper housing off . To my surprise I found no screws holding gear housing cover in place. You could tell they were there at one time. Should be 4. I removed cover disasembled what was left of gears. Cleaned old grease ordered parts. Thought since there was only 1 screw on diagram it would ship 4. No big deal. After recieving parts further inspection revealed no screws holding motor in place. This blows me away. Anyway off to local hardware store for more screws. Got home slapped it togethere in 10 minutes. Ordered this off TV about 6 years ago. They must have had it in for repair and forgot to put it back together. All that aside it runs better than ever. Thanks much Michael
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Brookings, OR
- Parts Used:
- W11086780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
mixer beater quite
disassembled unit gear head and replaced broken part, then reassembled
Was this instruction helpful to you?
Thank you for voting!
Worm Gear teeth was stripped
Removed top cover, remove snap-ring on shaft, slide top gear and worm gear off. Clean all the grease out and clean parts. Installed new worm gear and parts. Repacked with new grease, careful not to much, leaving room for expansion.
Was this instruction helpful to you?
Thank you for voting!
The motor was running but the mixer wasn't turning
After trying to make a batch of heavy frosting, my KitchenAid mixer final stopped turning. After watching a video of how to change the grease in a similar model on PartsSelect and seeing it wasn't that hard to take apart, I decided to give it a try myself. Removing the cover exposed a completely worn gear drive. Luckily, it was easy to determine which parts needed replacing and PartSelect sent them in no time. Once I put everything back together, it sounded terrible which was pretty tough to take. As it turned out, the problem was flecks of metal from the gear were still in the grease and were getting caught in the mechanism. Once I thoroughly cleaned all the grease out and gave it some fresh grease the machine worked great. Much better than before. I only wish I had swapped the grease out at the same time. Thank you PartsSelect for saving me hundreds of dollars on a new machine!
Was this instruction helpful to you?
Thank you for voting!