8KP2670 Whirlpool Mixer - Instructions

Removed the cover. Removed the gear assembly cover.. Extracted the C clip with a tool. Removed the bevel gear. Pushed out the dowel pin. Used rubber mallet to push the shaft off the worm gear. Replaced the washer and the worm gear. Used a 1/2" diameter PVC, 3" long over the shaft and on the gear to push back the shaft through the gear with rubber mallet. Pushed back the dowel pin. Reinstalled the C clip. Replaced broken hub bevel gear. Added more grease. Placed the gear cover with 4 screws just tight enough to hold the cover but still allows movement. Turned the mixer to the lowest speed. Allow the cover to self adjust so that the gears have the smoothest sound. Tightened the screws while while maintaining the smooth sound. Turned off the power. Replaced the cover.

I had previously ordered several other gears after I found one of the worm gears stripped. After putting it all back together, the one major gear in the unit that I had not replaced because it looked fine, the bevel gear, also stripped. Learning experience: this is a unit worth several hundred dollars, so don't skimp on a $4 part. Once you work on this thing, you might as well spend a few bucks more and replace ALL the gears - even if they look like they are okay. Furthermore, if you only take 15 minutes to do this repair, as some on this site suggest, you are probably not cleaning the old grease carefully enough. Make sure you properly clean out the old grease to remove any metal from stripped gears, and use a good quality grease to re-pack the gear case.

First and foremost, I am not mechanical at all. I typically refer to parts as thing-a-ma-jigs, and whatca-ma-call-its. When it froze up and started to make a loud grinding noise, I guessed it was a gear problem. I decided to try to take it apart, What did I have to lose? If I couldn't figure it out, I would be down a mixer. I was already down one as it was. It was very easy to take apart and I could immediately see what gears needed to be replaced. Parts Select made it very easy to see what parts I needed. And delivery was lightning fast; the next day after it shipped! I found a PDF on line on how to dis-assemble and re-assemble the mixer. I got it together and it mixed for a few minutes and froze again. I took it apart and realized that I didn't have the whatcha-ma-call-it (worm gear) seated properly. Fixed it and put it back together and put it to the test. Working just fine now! Thank you Parts Select for making this very easy!

Ordered new worm gear and received in a few days. I cleaned out old grease from the gear housing, replaced the worm gear and packed with new grease. Machine runs well now. Easy repair.

removed the cover as stated in the e-mail and followed their recommendations on how to do the repair, the hardest part was removing the retainer clip, job went smoothly. thanks

took off the strap band around mixer, took off the cover (4 screws, took off gear cover (4 screws) took off the retaining ring(used pliers and screwdriver) took off upper gear, took out retaining pin, took off lower gear (becareful to grab the planetary assembly as it will fall out after you take out the retaining pin) cleaned out all of the gear grease (the teeth that were missing were in it. replaced the planetary assembly, lower gear and retaining pin. replaced the upper gear, replaced the retaining ring (used screwdriver and hammer. you have to spread the ring with end of screw driver so it will fit on the shaft then tap lightly with screwdriver and hammer to get it down to the keyway for the ring.) replaced the gear grease with NEW grease, reaplaced the gear cover, replaced the mixer cover, replaced the strap band and plugged it in to test it. IT was quieter than before and works great. i spent less than $30 to repair my 10 year old, out of warranty, Kitchen Aid Mixer. much better than the $32.00 to ship it to factory repair shop and get an estimate to repair. I needed it to make a cake for my nephews wedding. I had my parts in 2 DAYS!!! it was a great experience over all.

I replaced the switch component twice and I still have the same problem. I will purchase a new motor now see if that works? I'll post what happens thanks

Following Replacement Part Youtube instructions, I disassembled the mixer and found what caused the sounds and prevented the mixer from operating. The worm follower gear had been ground down by the worm gear. I found that the shaft from the planetary gear had not been adequately greased and siezed preventing the worm follower gear from turning. The worm gear is obviously made of harder material and thus, was able to wear away the follower. I appreciate the your help which saved having to replace a perfectly good/expensive mixer. Thanks.

Looked at the schematic for this model on Parts Select. Removed Aluminum band screw, removed the 4 screws that hold the top of the mixer. Lifted the top off. Removed 4 screws and lifted the gear case. Removed snap ring and took off tapered gear. Removed pin and removed worm gear. Picked out the metal, in the grease, from the old worm gear, using a magnet then inserted new worm gear and put it back together in reverse order. There was plenty of grease and didn't need to add any.

remove the cover,take out four screw from gear box,remove the gear box,clean all gears,then you see damage gear,replace it ,install new grease.

I have to thank you at Partselect.com. You happen to help me help other people. Now I have several people bringing me their Kitchenaids to me instead of sending them in. I replaced two worm gears on a Kitchenaid 6 and the Hall sensor on a Kitchenaid 5. Very easy to do. Next week I have another Kitchenaid 5 to replace the motor on. Thankyou again for having the parts I need

Took housing off, removed computer board and disconnected speed control assembly from board. Soaked plastic slide in hot water and freed up mech. Discovered a crack in plastic slide from forcing it. Ordered new assembly and installed. TIP: Keep slide clean of substances that will jam it by cleaning occasionally with water. For a complete cleaning you will have to remove it. Total of 6 easy to reach screws.

Took mixer apart and then the gear compartment. inspected components. Replaced the worn gears and re-greased the new parts. Put the gear compartment back together, tested the operation of the unit and then replaced the rest of mixer, re-tested and declared victory.

___ Remove silver decorative band/1 screw ___ Remove top of mixer/4 screws ___ Remove circuit board/2 screws ___ remove 5 wires from ckt. bd. (be sure where they go) ___ Install new ckt. bd. with proper electircal connections ___ test mixer/OK ___ Reassemble & retest/OK

I looked on line found the product sent in information and 3 days later was in my mailbox,great service and ease of ordering. thanks marjorie