5KSM150PSDHT0 Whirlpool Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Henry from CAMPO, CA
- Parts Used:
- WPW10191926
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
1960s Kitchenaid K45 Mixer Screw Cap Stripped
My early '60's Kitchenaid K45 mixer screw cap/base plate would no longer hold the bowl, so I looked for another. This item, though not an exact replica of the original, fit and works great. The design is better by being more stout than the original. Pretty straightforward installation: remove three screws, take out old base plate, install new plate and screw down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Cupertino, CA
- Parts Used:
- WPW10112253
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Stripped gear when I tried to make Pizza Dough
Very messy as there is lots of heavy grease inside the mixer and you have to fish out the blown gear parts. I vary glad I took shop class in High school as it preped me for the job. The machanical drawing you provide were very useful but you should mention the grease.
Mixer works just like new. and I got the parts in two days with standard shipping. Pizza on Thursday and fixed by Saturday
Mixer works just like new. and I got the parts in two days with standard shipping. Pizza on Thursday and fixed by Saturday
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Rochester, NY
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wire broke
total replacement
works beautifully
works beautifully
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Pigeon, MI
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Worm gear was missing teeth
Took the mixer apart and cleaned the grease so off I could see the pins. Wasn't a hard fix only thing is make sure to clean the grease off so you can see what your doing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- terry from eudora, AR
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
very simple could not been a easer job thank for partsSelect.
all that were required, were you take off old beater an replace new.simple push up old part an replace new. as you do after usage of the machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- .JENNIFER from STAR, ID
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
powder coating came off mixer paddle.
put new paddle on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from Marshfield, WI
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The coating was chipping off of the original Flat Beater
All I had to do was insert the new beater. Wonderful timing, was just going to start some holiday baking. will definetly use your website again. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juanita from Ferndale, CA
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
beater was worn out
Insert and off you go. No real installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juanita from Ferndale, CA
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new flat beater
Just replaced the beater.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Columbus, OH
- Parts Used:
- WP16910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Pin was missing on mixer allowing head to move.
Inserted new pin and tightened set screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from CARLISLE, PA
- Parts Used:
- WP9709707
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing pedestal foot
Turned the mixer on its side and slid the part into the bottom of the base.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Burnsville, MN
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
When using the bread hook, the force of the dough would knock the bowl out of the retaining ring on the mixer (Cap-Screw.)
Three phillips-head screws held the "Cap Screw" in place on the stand of the mixer. After cleaning the stuff out of the screw slots, the screws came out surprisingly easy. After the plate was lifted off, we cleaned the residue from under the plate, placed the new one in position and easily screwed in the 3 screws.
We were very pleased by the quick delivery of the part.
We were very pleased by the quick delivery of the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darlene from North Liberty, IN
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Kitchenaid has bad white coated beaters that peal off
None
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Great Bend, KS
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace base plate on KitchenAid mixer
Took out 3 screws, removed old plate, put down new plate the tightened screws. Runs like new, great service, price, quick delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennife from Lancaster, PA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Worm gear broken
I called my fiancée.
Was this instruction helpful to you?
Thank you for voting!