5KSM150PSPER5 Whirlpool Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ernet from Birmingham, AL
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No repair I purchased a part.
The part fit great! PS. I may need to buy a gasket to go around my refrigerator door. I have an Amana Model #THI1853W, Serial No. 9502301998. Do you have instructions on how to install this gasket?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PJ from Rome, GA
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Part to KitchenAid Mixer
Great experience. Reasonable cost. Quick delivery. Would certainly use PartSelect again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jennie from cupertino, CA
- Parts Used:
- WPW10674618
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost dough hook so no repair
Just put it on and my challah was perfect!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deanna from Saint Joseph, IL
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Coating on original flat beater was cracking.
I just replaced my old flat beater with the new one. It fit and worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Crivitz, WI
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I had lost the thumb screw
I sent for a new thumb screw and screwed it in where it belongs and now I can use my other attachments.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gennette from Yuba City, CA
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Coating On My Flat Beater Had Chipped; Did Not Think It Was Safe Continue Using.
It was actually not a repair problem; just a replacement of a part. I ordered it one day and the next day the part was here. I have never had such a quick turn around in anything I have ordered. Thank you!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Altadena, CA
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Worn out worm (nylon) gear.
Followed up by your précised video, and print copy's which helped me a lot. That's easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wade from McDonough, GA
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
Beater/Mixer Ran many hours, Rubbed paint off tip
Ordered new paddle beater, rmoved old beater from mach, took new beater from plstc bag, inserted into mixer in appropriate plc, turned on mixer. YES!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Spring Valley, CA
- Parts Used:
- WPW10191926
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
37 year old screw cap worn, wouldn't hold bowl with heavy dough
Easy removal of old screw cap, but new one didn't just drop in. Had to scrape paint and a little aluminum to make it fit. Finally did, and it works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gordon from Seneca, SC
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Mixer jammed, then would not mix, motor ran
Wish that I had known about the video before disassembling. I did not know if it needed a part or was just jammed. It was clear that i needed a worm gear. So I ordered that. It turned out that I needed the Pinion Shaft w/ gear too. So another order. The shipping far exceeded the cost of the parts. NOTE: Clear off as much grease as necessary to be certain that there are no stripped gears anywhere, the order the parts. I took the mixer head off of the stand. I would suggest that you take a bath towel, roll each end towards the center, and place the mixed head so that it is supported on both sides by the towel rolls. NOTE2: Shipping was great 2 days or less. One part arrived on a Saturday. P>S> I do not know the age of this mixer. The age drop down menu should have an UNKNOW option.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Georgianne from Castro Valley, CA
- Parts Used:
- WPW10112253
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
My kitchenaid stopped moving
My husband looked at youtube to figure out what the issue was. He saw a video that identified that the likely problem was the worm gear. My husband took the kitchenaid applicance apart, as he saw in the video. We ordered the part, it took less than a week to arrive. He rewatched the video that demonstrated how to put the kitchenaid mixer back together. It's a bit messy due to all the packing grease, but a pair of nitrile gloves, paper towels, and an old rag help. We put a garbage bag over the appliance after it was taken apart to protect it from any dust and my curious cat. We let the kitchenaid cycle for about a minute to make sure the gear was greased. I haven't used it to make bread yet, but I'll do that soon. Thanks for supplying the part that saved us at least one hundred dollars and TRY to get a person who will repair small appliances.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erwin from Northport, ME
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Worm gear broken.
Followed directions video on line. good directions.
Was this instruction helpful to you?
Thank you for voting!
The speed control lever was bent and broken from a fall
Per a video on this site, I removed the stand part, then removed the rear electrical cover and aluminum band which wraps around the mixer. Next, remove the drip ring and planetary gear (use a punch). Then remove the 4 screws securing the bottom housing and the 5 screws around the planetary gear housing. You should be able to pull the upper and bottom housings apart now. This exposes the control lever. Just unscrew it and replace it. Re-install all parts in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Miya from Seattle, WA
- Parts Used:
- W11544572
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Base lost grip
Put on a new base plate using fresh screws, all ordered on Parts Select in under a minute. Now my grandmas old Kitchen Aid Stand-up mixer is as good as new! This was way easier than I thought it would be and really a great experience!
Was this instruction helpful to you?
Thank you for voting!