KSM154GBQ4KG0 Whirlpool Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from COXS CREEK, KY
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bowl lock wouldn't hold when mixing bread
Repair is very straight forward. Remove the existing plate by removing the three phillip head screws. Use a regular screwdriver or knife to pop the plate off. (I cleaned the area while I was there but probably not necessary) Position the new plate with the screw holes lined up. Press down to pop the plate into position. Install original screws and tighten. You're done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from MARION, IN
- Parts Used:
- WPW10112253
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
The mixer would not spin so I assumed it was a bad worm gear
I watched a video on how to replace the worm gear. When I opened the mixer I noticed a small screw laying in the grease. I removed as much grease as I could and could not find anywhere that the screw would have come from. All the gears turned and looked fine so I replaced the grease put the mixer back together and it worked fine. I am thinking the small screw must have somehow fallen into the mixer when manufactured. So proud of my 70 year old self for getting the job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from LEXINGTON, SC
- Parts Used:
- WPW10672617
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The white enamel coating was breaking off the mixer beater. There was a scrapimg noise when the beater was in motion.
I simply inserted the new beater into the mixer to see if it scraped the sides of the bowl. It fit perfectly and didn't scrape the bowl like the old one did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from HUNTINGTON, IN
- Parts Used:
- WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Worn Worm gear. Mixer made a clunking noise and wouldn't turn.
Followed your instructions from the internet and it was a simple fix. Mixer works great again. Thank You ..you made it easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Salina, KS
- Parts Used:
- WP67500-55, WP4162324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Leaking Grease
First i went to the Kitchen Aid web site and found a video on how to take a part the mixer. Followed the instructions from the video and it was very easy. The grease in the machine was black so i cleaned it out of the transmission and repack it with hi-heat wheel bearing grease that i got from a auto parts store it took about a 1/2 lb. then put the gasket in and back together and put the o-ring on. Have run for awhile and it is ok. Want to say that these are very well built machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from Hemet, CA
- Parts Used:
- WP67500-55, WP4162324
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
grease from housing leaking into bowl
Followed instructions found onllne at Kitchenaid.com and replaced seals with parts obtained from PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRIAN from PALISADE, CO
- Parts Used:
- WPW10112253, W11192794, WP4162324
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Decorative plug at top of mixer fell into the bowl and jammed the mixer stripping gears
Watch U Tube video. Take care to keep track of disassembly. Hard part was to have 4 types of screw drivers to fit the different screw heads. Be sure to clean broken gear clogs out of the grease. Parts select lady was a great help. Download Parts select diagram for extra help. Time and patience!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from CHARLESTON, SC
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The threads on the plate that holds the bowl had stripped and the bowl flew off when mixing
Removed old plate, screwed in new plate and works like new! Was so happy I wouldn’t have to replace my 30 year old mixer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sylvia from HILTON, NY
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The original screw cap would not hold the mixer bowl in place anymore.
The new part was too large for the replacement job, but we used the self tapping screws that came with the mixer and screwed them in from the bottom to open the holes a little more since the original screws were to short to hold the new plate. Then we replaced the screws with longer screws and that seemed to do the trick!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sabrina from BUNKIE, LA
- Parts Used:
- WPW10380496
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burnt brushes
The brushes are located on each side of the tilt head of the mixer. I used a screwdriver to remove the screws, removed the brushes & replaced with the new ones. Runs great again!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mrs Brenda from LYNNWOOD, WA
- Parts Used:
- WP9709194
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Screw cracked on the front of the mixer
Skewer the screw in with my fingers,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from MILWAUKEE, WI
- Parts Used:
- W11192794
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
EXTRUDER GEARS GROUND DOWN AND STOPPED WORKING
Dismantled the mixer, took photos, and re-assembled unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from BATTLE GROUND, WA
- Parts Used:
- WPW10191926
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
old stand mixer mixing bowl base will not firmly hold newer mixing bowls
With a screw driver remove the screws holding the old base in place. With a flat head screw driver carefully pry and remove old mixer base. With 600 grit sandpaper clean and make smooth any burrs or rough spots in the mixer base recessed area. You can use some light grease and coat the outer edges of new mixer base and place in the now cleaned mixer base recessed area. The new base maybe a tight fit and not be fully seated in the recess. If a tight fit, place the piece of 2x4 piece of wood over the new part that is in the recess and carefully tap the base home using the sledge hammer. Check to see, if the base is fully seated. If not fully seated, tap again When fully seated replace the screws. You may have to adjust the height of the stand mixer head with mixer paddle attached for proper clearance between bowl and paddle. See your mixer manual for adjustment procedure
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CEDAR CITY, UT
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Plastic worm gear gave way (as designed) when the grain mill over-worked it.
I did exactly what the PartSelect video demonstrated after watching other DIY videos on the Internet, thus I did not remove the stand which seemed like a little too much for a simple straight forward repair. This is the second time I have replaced this gear. The first time was about 10 years ago when the bakelite gear broke on a 30 year old KitchenAid K
-45. That mixer made hundreds of loaves of bread after grinding many pounds of wheat berries. The only reason we had to replace it was that it walked off the flour dusted counter and landed on its head when my wife had her back turned. Otherwise we would still be using it. :-)
Thanks for the excellent service and instructions.
-45. That mixer made hundreds of loaves of bread after grinding many pounds of wheat berries. The only reason we had to replace it was that it walked off the flour dusted counter and landed on its head when my wife had her back turned. Otherwise we would still be using it. :-)
Thanks for the excellent service and instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from SALINAS, CA
- Parts Used:
- WPW10112253, WP9709280
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Kitchen Aid Mixer won't spin
Order the worm gear part number PS11748374.
Watch this video.
https://www.youtube.com/watch?v=VeCiivPt7hk
I would recommend two people if possible.
Watch this video.
https://www.youtube.com/watch?v=VeCiivPt7hk
I would recommend two people if possible.
Was this instruction helpful to you?
Thank you for voting!