KSM150FBER0 Whirlpool Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gonzalo from HAINES CITY, FL
- Parts Used:
- WPW10380496, WPW10330804, WPW10325124, WPW10119326
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Motor did not turn on.
I removed the excess of grease to clear all parts. Then I installed new mechanical parts. Finally, I installed all electrical parts. I followed a logical sequence of removing and installing steps. Tip: Never remove parts without a logical order of sequence.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ethel from Crystal River, FL
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
thumb screw broke
it just screw in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bedalia from Rialto, CA
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Replacement of digital window in oven unit
I did not do the repair myself, however, I contacted a suggested service company which in turn was a company I had used before when I had problems with my JenAir microwave. Excellent service, prompt and very professional. Thank you JenAir for your assistance in providing promptly the parts needed to complete this job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Laramie, WY
- Parts Used:
- WPW10191926, W11544572
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I was missing parts to stand mixer
simply put it together, .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Valencia, CA
- Parts Used:
- WP16910
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
The head of my machine was sagging
and I thought replacing the hinge pin would fix it, I used an awl to push out the old pin then used the new pin to push the old one all the way out. That did not fix the problem. Went to a store to look over a new one and saw that the screw under the head at the hinge point on the new machines was not screwed in tight. Turns out that screw is the "bumper" for the head against the neck, so the head is held back by the screw. FIXED
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Reno, NV
- Parts Used:
- WPW10380496
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Motor would not turn on
Initially removed carbon brushes then inserted the new carbon brushes. The motor still did not turn on. Then I removed the brushes again, used a flashlight to look in the hole where the carbon brushes are installed. I noticed that there was a square notch on one side of the hole. I then reinstalled the carbon brushes, ensuring that the beveled side of the carbon brush was installed so it lines up with the square notch. This allows the carbon brushes to touch the motor. I turned the unit on and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Craryville, NY
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wire whip brokrn
Just screwed it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Miya from Seattle, WA
- Parts Used:
- W11544572
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Base lost grip
Put on a new base plate using fresh screws, all ordered on Parts Select in under a minute. Now my grandmas old Kitchen Aid Stand-up mixer is as good as new! This was way easier than I thought it would be and really a great experience!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from Tracy, MN
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic worm gear stripped
The plastic worm gear was stripped,I took it apart first then cleaned out all the old grease so when the new part came it together like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PJ from Rome, GA
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Part to KitchenAid Mixer
Great experience. Reasonable cost. Quick delivery. Would certainly use PartSelect again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jennie from cupertino, CA
- Parts Used:
- WPW10674618
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost dough hook so no repair
Just put it on and my challah was perfect!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deanna from Saint Joseph, IL
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Coating on original flat beater was cracking.
I just replaced my old flat beater with the new one. It fit and worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Salem, IL
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The thumb screw plastic came off
Open the package with the new screw and it looked like the screw was wider. I tried it to see if it goes in and as long as you screw it straight in, there was no problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Manheim, PA
- Parts Used:
- WP9709707
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Lost a rubber foot on my Kitchen Aid mixer. The remaining feet we're hard and mushroomed. I decided to replace all 5. That was the correct decision.
I griped each foot with a pliers and twisted it out of its setting. I then set a new foot in place and hammered it into place with a small hammer. The feet fit snugly and did not need to be glued. Job was easy and mixer sits like new. I was glad I spent the money to replace all of the feet at once.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Crivitz, WI
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I had lost the thumb screw
I sent for a new thumb screw and screwed it in where it belongs and now I can use my other attachments.
Was this instruction helpful to you?
Thank you for voting!