KSM150FECU0 Whirlpool Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Hilton from GREENVILLE, SC
- Parts Used:
- WPW10380496, WP9709194, WP9704329
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Motor speed was erratic and no high speed
Removed the rear cover to inspect the speed board. Replaced motor brushes and noticed the motor body nuts were loose and 1 was completely off. Cleaned up speed board and replaced the motor body nuts, tightened with nutdriver, adjusted speedboard governor screws and with new motor brushes worked like a charm. The very rough sounding motor noise was gone and the mixer has not operated so quietly ever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheldon from RICHMOND, TX
- Parts Used:
- WPW10112253, WP4162324
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench (Adjustable)
Hard to knock out pins, and connecting the top to the bottom after repair
watched how to repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curt from SHELBY, MI
- Parts Used:
- WPW10112253
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Teeth on the gear were worn off.
Took each area apart. Replaced the gear and reassembled it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CEDAR CITY, UT
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Plastic worm gear gave way (as designed) when the grain mill over-worked it.
I did exactly what the PartSelect video demonstrated after watching other DIY videos on the Internet, thus I did not remove the stand which seemed like a little too much for a simple straight forward repair. This is the second time I have replaced this gear. The first time was about 10 years ago when the bakelite gear broke on a 30 year old KitchenAid K
-45. That mixer made hundreds of loaves of bread after grinding many pounds of wheat berries. The only reason we had to replace it was that it walked off the flour dusted counter and landed on its head when my wife had her back turned. Otherwise we would still be using it. :-)
Thanks for the excellent service and instructions.
-45. That mixer made hundreds of loaves of bread after grinding many pounds of wheat berries. The only reason we had to replace it was that it walked off the flour dusted counter and landed on its head when my wife had her back turned. Otherwise we would still be using it. :-)
Thanks for the excellent service and instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from HALEYVILLE, AL
- Parts Used:
- WPW10325124
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
One speed only and surging
I replaced the phase control board because the mixer had only
one speed and was surging. I noticed from other posts that it
is important to note the setting of the speed plate before you
remove it in order to remove the phase control board. Also be
careful removing the associated 'slip-on' terminals as it would
be easy to damage the speed plate. If I ever do this again I
will go ahead and replace the speed plate, probably the cheapest
item to replace. The operation was a success and the mixer is
back in business. Thanks.
one speed and was surging. I noticed from other posts that it
is important to note the setting of the speed plate before you
remove it in order to remove the phase control board. Also be
careful removing the associated 'slip-on' terminals as it would
be easy to damage the speed plate. If I ever do this again I
will go ahead and replace the speed plate, probably the cheapest
item to replace. The operation was a success and the mixer is
back in business. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from HAMPTON, NH
- Parts Used:
- WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My stand mixer stopped mixing!
I watched a YouTube video all the way through, then watched each segment and followed along with the video. It was messier than the professional repair guy, but it worked out fine. This is not a difficult repair when you can watch a video and follow along. It saved me about $130.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Kathleen, GA
- Parts Used:
- WPW10380496, WP4162324, WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Worms Gear broken teeth from the gear.
Followed web site's videos. One step left out of video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from SALADO, TX
- Parts Used:
- WPW10323373, WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Worm gear was worn out .
I watched the university of YouTube videos, and followed their instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jamie from FLORENCE, CO
- Parts Used:
- WP3184212
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Mixer making a grinding noise
replaced gear, and brushes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Athens, GA
- Parts Used:
- WP240309-2
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Mixer suddenly ceased operation after sharp noise
To access the interior of the mixer, I first removed the single screw holding the cup-shaped part at the rear. Then I removed the 4 large screws on the under surface of the mixer head. Next I removed the bright metal ring around the planetary gear area by prying it off. I then pried the dish-shaped part off the shaft using a large-bladed screwdriver. This exposed 5 screws on the circumference of the planetary gear. By removing them, one can pull up the gears and see into the area below. I found the worm gear had fractured. By removing 3 screws at the base I extracted it for closer inspection, checking for any loose pieces. Beware of the jelly-like grease. The replacement part goes into position, and one then follows the steps in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from UNICOI, TN
- Parts Used:
- WPW10380496
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Motor surges at some speeds
Tried new brushes but alas it looks like it was a controller. Wife needed it asap so Ii bought her a new one. Service and delivery were quick but couldn't wait for a second part to try and repair it again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from COLUMBUS, OH
- Parts Used:
- WPW10380496
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I noticed that the Initials on the package indicated that the part was made in CI. That was the problem.
I decided to update the motor brushes in our KitchenA id mixer even though it operated perfectly for years. After installing the motor brushes, you sent,I plugged the cord attached to the mixer into the outlet. I selected 1 on the speed selector and nothing occurred. The mixer would not operate. I then checked the outlet to insure there was voltage present; there was voltage present. I again plugged the cord of the mixer into the outlet, selected 1, then 5, and finally 10, with no results. The mixer would not operate. Finally, I removed the motor brushes I had received from you and installed the old brushes that were originally in the mixer, plugged it in the outlet, selected 1 and the mixer operated perfectly as it did BEFORE installing the brushes you sent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KATHERINE from INVERNESS, FL
- Parts Used:
- WPW10380496
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
over heating
followed the emailed instructions from your company
worked perfectly
thanks
worked perfectly
thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Lynchburg, VA
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wire whip got bent and had to be replaced
just inserted the new wire whip
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from St. James, MN
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wire whip came apart
Really no help from Kitchen Aid sources; but phone call to PartSelect solved the problem. Kitchen Aid repair line didn't even know the part #! Thanks to Part/Select, Christmas cookies are being made.
Was this instruction helpful to you?
Thank you for voting!