KP26M1XQ3PT5 Whirlpool Mixer - Instructions

Remove Beaty band, one screw. Remove four screws holding top. Remove worm gear, by simply lifting it out. Removed all grease. Repacked with fresh grease. Take out gear case/ transmission bearing, clear all old grease, repack with new grease. Install into new gear case housing. Assemble, and Repack new worm gear and front and rear worm gear bearings, utilize old washers (2), and one small ball bearing washer. Rotate worn gear and bushing to spread the new grease throughout the gears. Replace top cover, four screws . Replace beauty ring, one screw. Run unit for 20 to 30 seconds, under no load to distribute the new grease. Works like a charm. 45 minutes to one hour. To complete.

Removed the cover. Removed the gear assembly cover.. Extracted the C clip with a tool. Removed the bevel gear. Pushed out the dowel pin. Used rubber mallet to push the shaft off the worm gear. Replaced the washer and the worm gear. Used a 1/2" diameter PVC, 3" long over the shaft and on the gear to push back the shaft through the gear with rubber mallet. Pushed back the dowel pin. Reinstalled the C clip. Replaced broken hub bevel gear. Added more grease. Placed the gear cover with 4 screws just tight enough to hold the cover but still allows movement. Turned the mixer to the lowest speed. Allow the cover to self adjust so that the gears have the smoothest sound. Tightened the screws while while maintaining the smooth sound. Turned off the power. Replaced the cover.

Great experience. Reasonable cost. Quick delivery. Would certainly use PartSelect again

I sent for a new thumb screw and screwed it in where it belongs and now I can use my other attachments.

replaced Speed control board. less than 40.00 took ten minuets from the time I started until we were making cookies.

opened the mixer.. all screws in kitchaid are the same so not to worry... opened up and replaced the gears... and put it back together... diagram helped in that front and rear bearings of connecting gear are the same # on diagram it is easy to confuse when you put it back together, but the item number and description of each helped make sure it was in the right place. Otherwise... time to fix would have been less....

took mixer cover off, took gear box cover off, removed gears, replaced gears, replaced covers, made cookies, no problem!!

removed top casing, removed old switch and sensor,and replaced with new ones. It was just a matter of a half dozen screws and unpluging 4 or 5 wires and then reversing the process. Couldn't be easier. thank you

I replaced the switch component twice and I still have the same problem. I will purchase a new motor now see if that works? I'll post what happens thanks

took off the strap band around mixer, took off the cover (4 screws, took off gear cover (4 screws) took off the retaining ring(used pliers and screwdriver) took off upper gear, took out retaining pin, took off lower gear (becareful to grab the planetary assembly as it will fall out after you take out the retaining pin) cleaned out all of the gear grease (the teeth that were missing were in it. replaced the planetary assembly, lower gear and retaining pin. replaced the upper gear, replaced the retaining ring (used screwdriver and hammer. you have to spread the ring with end of screw driver so it will fit on the shaft then tap lightly with screwdriver and hammer to get it down to the keyway for the ring.) replaced the gear grease with NEW grease, reaplaced the gear cover, replaced the mixer cover, replaced the strap band and plugged it in to test it. IT was quieter than before and works great. i spent less than $30 to repair my 10 year old, out of warranty, Kitchen Aid Mixer. much better than the $32.00 to ship it to factory repair shop and get an estimate to repair. I needed it to make a cake for my nephews wedding. I had my parts in 2 DAYS!!! it was a great experience over all.

We are a pretty handy bunch here. However, the diagrams provided with the part numbers did assist in the disassembly. It went smooth and easy.

Removed one screw to remove deco band around mixer body. Removed four screws under band to remove mixer top. Removed two screws holding switch. Removed wires one at a time putting them in the same position on the new switch. Re-attached switch, mixer top, and deco band. Works perfectly.

Removing the cover of the mixers "guts", it was immediate evident the a major gear had lost a few of its "teeth". Parts Select clearly offered the required part of this $300 mixer for a favorable price. I was fully impressed that it arrived within 4 days or my ordering the part. I simply exchanged the damaged gear and restored the mixer to service and I'm fully impressed with the Parts Select Company for their swift response to my needs.

remove the cover,take out four screw from gear box,remove the gear box,clean all gears,then you see damage gear,replace it ,install new grease.

the plastic covering the thumb screw cracked almost half way and lost the piece....so the new one is being used to replace this old one...very easy to install