KP26M1XQ3CU5 Whirlpool Mixer - Instructions

ordered the part and put in in with the help from the instant repairman

removed cover. Removed cover over gears. Used lock washer pliers to remove lock washer. Took out gears. Cleaned metal shavings from old gear and grease. Reassembled using new gear. Took about 15 minutes and saved $$ over sending mixer out for the repair.

I unplugged the mixer, then I removed the Phillips screw holding the beauty ring, then removed the 4 screws that hold the motor housing together. I removed the housing top, and unscrewed the speed control switch. I marked each one of the connectors of the switch (there are 4) 1-4 then disconnected the speed sensor from the switch and the motor. Replaced the new sensor and connected that to the new speed control switch. reconnected the connectors to the terminals I took them from ( 1 - 4 ) screwed it into place. replaced the top motor housing, I screwed that back with the four screws. replaced the beauty ring and screw. plugged it in and tested it and it was like new

I have to thank you at Partselect.com. You happen to help me help other people. Now I have several people bringing me their Kitchenaids to me instead of sending them in. I replaced two worm gears on a Kitchenaid 6 and the Hall sensor on a Kitchenaid 5. Very easy to do. Next week I have another Kitchenaid 5 to replace the motor on. Thankyou again for having the parts I need

Remove screw and nut from back of mixer head to release the silver name band. Remove the exposed four cross head screws, (two each side), and lift off the motor and gear cover. Wipe excess grease from gear wheels to expose the retaining ring clip at top of vertical gear shaft. Using small nose circlip pliers, remove retaining ring and bevel gear wheel to expose shaft pin and worm gear. Support the shaft from below and remove pin. Lift off worn worm gear wheel allowing shaft to drop down. The horizontal worm gear shaft can now be lifted out taking care to keep assembled. Carefully clean old grease from all gears and from the gear housing, (note that broken pieces of the old worm gear are in the old grease. Repack housing with fresh high performance grease recommended for worm drives. Cover new and reuseable gears with grease. Reverse the process to reassemble the unit.

Looked at the schematic for this model on Parts Select. Removed Aluminum band screw, removed the 4 screws that hold the top of the mixer. Lifted the top off. Removed 4 screws and lifted the gear case. Removed snap ring and took off tapered gear. Removed pin and removed worm gear. Picked out the metal, in the grease, from the old worm gear, using a magnet then inserted new worm gear and put it back together in reverse order. There was plenty of grease and didn't need to add any.

Took housing off, removed computer board and disconnected speed control assembly from board. Soaked plastic slide in hot water and freed up mech. Discovered a crack in plastic slide from forcing it. Ordered new assembly and installed. TIP: Keep slide clean of substances that will jam it by cleaning occasionally with water. For a complete cleaning you will have to remove it. Total of 6 easy to reach screws.

___ Remove silver decorative band/1 screw ___ Remove top of mixer/4 screws ___ Remove circuit board/2 screws ___ remove 5 wires from ckt. bd. (be sure where they go) ___ Install new ckt. bd. with proper electircal connections ___ test mixer/OK ___ Reassemble & retest/OK

Following Replacement Part Youtube instructions, I disassembled the mixer and found what caused the sounds and prevented the mixer from operating. The worm follower gear had been ground down by the worm gear. I found that the shaft from the planetary gear had not been adequately greased and siezed preventing the worm follower gear from turning. The worm gear is obviously made of harder material and thus, was able to wear away the follower. I appreciate the your help which saved having to replace a perfectly good/expensive mixer. Thanks.

The repair is actually quite simple. The Snap Ring Pliers are essential. Make sure you clean out all the old grease in the machine and replace with new grease. The metal dust will act like sandpaper and destroy your new gear. There are several videos on YouTube which go through the process of repair and part replacement, I found these quite helpful. Good luck! DIY!!!!

Noticed worm gear was worn out, ordered the parts, it came very next day. On YouTube instructions were very easy to follow. Important point to remember,I washed the parts in water with chlorine in it. Retaking ring was tough to take out, as I did not have parrot beak plier, could not find it at Home Depot or Lows. Putting the retaining ring I used circular nut driver, to press it on the shaft to slide down by hammering it. While assembling follow the instruction step by step from the you tube. Machine works smoothly. Performing well. Thanks to part select, excellent web page, efficient delivery. I would recommend them to all.

Used the meat grinder attachment, with the retaining ring too tight for the motor to turn the augur, so a gear stripped and the mixer would not run. I opened the mixer top, removed the transmission cover, removed enough grease to diagnose the problem (6 teeth stripped off the steel worm gear). I ordered a replacement steel worm gear and, while I was at it, a new retaining ring, bevel gear, retaining pin and the large planetary gear, as I could not tell the condition of these until I disassembled the whole gear train. I then removed the gear train components (needed a snap ring pliers to remove the retaining ring -- I don't recommend trying to remove it with an y other tool), washed them in acetone, cleaned out the transmission case and went over it with a magnet to get stray gear tooth remnants, replaced the worm and bevel gears and reassembled, using the original planetary gear, retaining pin and retaining ring. Filled the bottom of the transmission with planetary grease first, then, once the gear train had been replaced, slathered a big pile of grease over it, replaced the transmission cover. The machine then ran perfectly, so I replaced the mixer's top cover and decorative band and was back in business mixing with it about 30 minutes after cleaning the last of the grease off my hands. I should mention, I used a LOT of paper towels for this job. This was a fun job and I was sorry that it was so easy to do, as I enjoy working with gears and grease.

took mixer apart down to removal of gear case cover.upon removal of this cover found the bevel gear and hub bevel gear chewed up .removed them both then replaced them both.and also had to solve a clearence problem between the 2 gears they were too loosely meshing. so had to push the hub retainer closer to take up the meshing slack.not sure my repair will hold but i have another set of gears and another solution that will surely fix it.

Worm gear strips usually after the lower gear housing breaks. Tore down cleaned grease and shrapnel out, replace stripped worm gear and lower housing. It's convenient that the lower housing plate comes assembled with new bushing and gear. This is now the third one of these expensive mixers I have repaired, word got out that I fix them, and this is a very common problem. Repairs have been for friends and Church, so I don't charge any labor, it's kind of fun, messy, but fun. Note to Kitchen Aid: Please strengthen lower gear case.

After trying to make a batch of heavy frosting, my KitchenAid mixer final stopped turning. After watching a video of how to change the grease in a similar model on PartsSelect and seeing it wasn't that hard to take apart, I decided to give it a try myself. Removing the cover exposed a completely worn gear drive. Luckily, it was easy to determine which parts needed replacing and PartSelect sent them in no time. Once I put everything back together, it sounded terrible which was pretty tough to take. As it turned out, the problem was flecks of metal from the gear were still in the grease and were getting caught in the mechanism. Once I thoroughly cleaned all the grease out and gave it some fresh grease the machine worked great. Much better than before. I only wish I had swapped the grease out at the same time. Thank you PartsSelect for saving me hundreds of dollars on a new machine!