5KSM185PSEKG4 Whirlpool Mixer - Instructions

I how the video for replacing the worm gear on your website. It help me a lot. I followed step by step instruction display on video. It was great help.

I took out the worm gear and replaced it with the new one. It is important to have the correct punches that are just under the diameter of the pins.

My husband looked at youtube to figure out what the issue was. He saw a video that identified that the likely problem was the worm gear. My husband took the kitchenaid applicance apart, as he saw in the video. We ordered the part, it took less than a week to arrive. He rewatched the video that demonstrated how to put the kitchenaid mixer back together. It's a bit messy due to all the packing grease, but a pair of nitrile gloves, paper towels, and an old rag help. We put a garbage bag over the appliance after it was taken apart to protect it from any dust and my curious cat. We let the kitchenaid cycle for about a minute to make sure the gear was greased. I haven't used it to make bread yet, but I'll do that soon. Thanks for supplying the part that saved us at least one hundred dollars and TRY to get a person who will repair small appliances.

followed the instruction on you tube

Task went EZ,I have two with bad transmission and with fixing them I found out the grease in case housing was bad like wax. So I'm going to check out my third mixer and replace old grease in that one. your part scrimatics are great thanks.

Took the mixer down to the gear box. Found the plastic drive gear had a few stripped teeth. Did a search on the internet for the mixer gear. Found a couple of suppliers. Ordered the needed gear, pin and a bearing block just in case it was worn. The bearing block did not need to be replaced. Cleaned the broken off teeth from the gear grease and put the mixer back together. All worked fine when I plugged it in.

I found a video on how to repair mixer that would not turn. Watched video several times and replaced worn worm gear. Getting the old worm gear was the most difficult part of the job. I had to go purchase a pin punch ($5.50) with the correct tool is was easy.

I discovered the brushes were worn, and one side had broken off and lodged against the armature.I got lucky as I removed the brush caps and the sleeves the brushes fit into (simple job) and was able to hand turn the armature so the pieces fell down into the bottom of the mixer housing.After removing them, I replaced the brushes and the mixer runs like new. Thanks for the fast delivery AND more importantly, the right part. Steve

Followed up by your précised video, and print copy's which helped me a lot. That's easy!

Followed directions video on line. good directions.

After I dropped a part of the shield into my mixer the motor screamed and I unplugged the mixer. I found out I had a broken worm gear. I then order the part and per the helpful video I did the repair and I also changed the brushes my mixer is up and running waiting for the holiday baking season thanks to Part select.com Very easy Instructions to follow I am very happy with the results. Thanks Barbara

i followed the instructions in video. Thank you joe

Wish that I had known about the video before disassembling. I did not know if it needed a part or was just jammed. It was clear that i needed a worm gear. So I ordered that. It turned out that I needed the Pinion Shaft w/ gear too. So another order. The shipping far exceeded the cost of the parts. NOTE: Clear off as much grease as necessary to be certain that there are no stripped gears anywhere, the order the parts. I took the mixer head off of the stand. I would suggest that you take a bath towel, roll each end towards the center, and place the mixed head so that it is supported on both sides by the towel rolls. NOTE2: Shipping was great 2 days or less. One part arrived on a Saturday. P>S> I do not know the age of this mixer. The age drop down menu should have an UNKNOW option.

Replaced electrical board and speed control plate. cleaned and added new grease. Removed agitator cover and replaced agitator with new. Problem agitator did not match existing. Old agitator was drilled and tapped for a plate to hold gear in place. Tried one without does not work.