5K45SSBSL4 Whirlpool Mixer - Instructions

Looked at the mixer schematic form your website,which made it easy for me to take it apart. Once it was apart & all the grease removed I disassembled & cleaned all the drive parts. Saw what was warn, ordered the parts from you. Three days later received the parts, everything fit perfect. Added grease,assembled the mixer and it ran perfect, good for another 20 yrs. Thank you for making it so easy to repair an old mixer in just over two hours. Rolf

Replace went good used the online video, my husband doesn't usually use any help but said the video helped him. Now my mixer works perfect. Also the price and shipping time was awesome.

Place Pin in hole where it was missing then gently tap pin into place
Run a test and all is good ??
make sure to use a drift pin set
Tom

Literally the whole top of this stand mixer had to be taken apart. With the help of U-tube! We realized the silver strip was removable and there where screws underneath. We figured we would replace both parts while it was all taken apart. We cleaned the mixer and added some grease where necessary. I now have a 25 year old new mixer. Thanks for having our parts and guiding us with a diagram of the unit. Very helpful.

We disassembled it with the help of a YouTube video from partselect.
We saw the damaged gear, removed the 4 screws to remove it, cleaned all the old grease out with rags so it wouldn't be contaminated by metal shavings.
We reassembled it per the YouTube video and it works better than ever!!
Make sure you remove the roll pin before trying to pry off the planetary plate, because I watched a different video first, which didnt tell me that and i bent it a bit.

Looked for the probable cause from a U-tube video, then found the parts list and repair video on the PartSelect website. When the parts arrived within 3days the shipped email had a video on exactly how to complete the repair. Repair video was very well done and easy to follow.

Repairing/replacing worm-gear (FSP part# W10112253) for a KitchenAid Stand Mixer model number K5SS. First: I am writing this story because all the videos or repair articles I’ve viewed are either misleading or incorrect in that they do not include older K5SS models. 1. These older models from the mid 1960’s or even earlier have four very large #4 chrome plated Phillips Head Screws holding the mixer base to the motor assembly and NOT four small machine screws (one with a lock-washer) as seen on other repair videos. In addition, the stand is composed of two separate pieces with the bottom half being held together with another four identical #4 chrome plated Phillips Head Screws. The upper four holding the stand to the motor housing (I used a manual impact driver to loosen the very stubborn, #4 Phillips screws) must be removed so as to access the four smaller Phillips machine screws (no lock-washers found here, best buy at least four #10, split, before reassembly) 2. Lastly, you will need two pin punches however the recommended smaller 3/32 inch is still too large to remove the pin in the tower assembly. You will need one size smaller or a #4 pin punch instead. These older Kitchen Aid mixers were built with very tight tolerances. Please be patient and take your time removing the pins. Good Luck……. Jim

I removed the pin from the outside shaft,then removed all screw around the body of the mixer,then removed the top case out,took 3 screws out from the the gear assembly case......punched the pin out of worm gear then release the little shaft out from the case,replaced a new one....then starting go backward till completely all assembled don't forget lube grease to all gears and test run good very smooth.........it's ok

I removed three screws, pulled off the old base plate.
Put new base plate in place and replaced the screws

Unplugged mixer. Removed screw holding cover on. Removed end seal. Inspected repair area for furhter damage. Installed new end seal and cover.

Just put on the new whip...exactly like old one.

Follow a YouTube video step by step

None

I removed the spring loaded brush screw on the side of my mixer and lost it the next day. I found a schematic of this part on your website and ordered the four pieces that make up the brush screw(?). They arrived in just a few days and I referred back to the schematic to put it together. I then popped it in my mixer, screwed it down, plugged her in and away we go! Easiest repair I’ve ever done! I’m a 70 year old retired lady and not very handy, but this was an easy fix! Thank you, PartSelect!

Unscrewed old Screw Cap, tapped it out with hammer. Replaced with new screw cap that was slightly different and tight. Tapped it in with piece of wood over it and hammered it on. No problems.