Models > 5KSM180LEABK0 > Instructions

5KSM180LEABK0 Whirlpool Mixer - Instructions

Jump to:

All Instructions for the 5KSM180LEABK0
106 - 120 of 189
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
H. from Hollister, CA
Parts Used:
WP240309-2
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Damaged the worm gear in our 300w mixer.
After stalling the mixer while mixing dough I found that the motor still functioned but the blade didn't move. I basically took the mixer into my shop along with a digital camera to record any complicated disassembly procedure I might have to deal with for reassembly and proceeded to disassemble the mixer. Once apart, I cleaned the mixer parts, removed the broken worm gear and bracket, and got online for someone that carried the replacement piece. PartSelect sent the replacement within 3 days and now it works great again.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Walter from Athens, GA
Parts Used:
WP240309-2
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Mixer suddenly ceased operation after sharp noise
To access the interior of the mixer, I first removed the single screw holding the cup-shaped part at the rear. Then I removed the 4 large screws on the under surface of the mixer head. Next I removed the bright metal ring around the planetary gear area by prying it off. I then pried the dish-shaped part off the shaft using a large-bladed screwdriver. This exposed 5 screws on the circumference of the planetary gear. By removing them, one can pull up the gears and see into the area below. I found the worm gear had fractured. By removing 3 screws at the base I extracted it for closer inspection, checking for any loose pieces. Beware of the jelly-like grease. The replacement part goes into position, and one then follows the steps in reverse.
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Harry from MILTON, WA
Parts Used:
WP240309-2
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Mixer still ran, but seemed to be getting very loose as if gears or a shaft were wearing out.
I followed the video provided online. The model shown was not exactly the same as mine, but very close. The step-wise progression demonstrated on the video helped a lot. I had to double check the video a couple of times which added to the work time....I could probably do it again without the video in under 1 hour. As shown in the video, I laid out an old towel across two pieces of 2x4 which helped keep the mixer head in a position that was easy to work on and also prevented scratches.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gonzalo from HAINES CITY, FL
Parts Used:
WPW10380496, WPW10330804, WPW10325124, WPW10119326
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
Motor did not turn on.
I removed the excess of grease to clear all parts. Then I installed new mechanical parts. Finally, I installed all electrical parts. I followed a logical sequence of removing and installing steps. Tip: Never remove parts without a logical order of sequence.
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carl from Austin, TX
Parts Used:
WP9704329
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken whip, no local availability
No nstallation required, simply attach.
Your website was the only one that made sense. I am blind and follow the instructions with a screen reader. I had no difficulty. It was much easier than this questionaire.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lee from Valencia, CA
Parts Used:
WP16910
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
The head of my machine was sagging
and I thought replacing the hinge pin would fix it, I used an awl to push out the old pin then used the new pin to push the old one all the way out. That did not fix the problem. Went to a store to look over a new one and saw that the screw under the head at the hinge point on the new machines was not screwed in tight. Turns out that screw is the "bumper" for the head against the neck, so the head is held back by the screw. FIXED
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tiffany from San Antonio, TX
Parts Used:
WP16910
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Pin fell out of neck
Placed pin in the hole...some wiggling had to be done for a tight fit. Installation complete!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lois from Albuquerque, NM
Parts Used:
WP9704329
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Wire Whip was coming apart
Replaced it with a new part. No installation or repair to maching was necessary
Was this instruction helpful to you?
Thank you for voting!
Customer:
Pete from Tracy, MN
Parts Used:
WPW10112253
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Plastic worm gear stripped
The plastic worm gear was stripped,I took it apart first then cleaned out all the old grease so when the new part came it together like a charm.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lawrence from Craryville, NY
Parts Used:
WP9704329
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
wire whip brokrn
Just screwed it in
Was this instruction helpful to you?
Thank you for voting!
Customer:
Miya from Seattle, WA
Parts Used:
W11544572
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Base lost grip
Put on a new base plate using fresh screws, all ordered on Parts Select in under a minute. Now my grandmas old Kitchen Aid Stand-up mixer is as good as new! This was way easier than I thought it would be and really a great experience!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dale from Manheim, PA
Parts Used:
WP9709707
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Lost a rubber foot on my Kitchen Aid mixer. The remaining feet we're hard and mushroomed. I decided to replace all 5. That was the correct decision.
I griped each foot with a pliers and twisted it out of its setting. I then set a new foot in place and hammered it into place with a small hammer. The feet fit snugly and did not need to be glued. Job was easy and mixer sits like new. I was glad I spent the money to replace all of the feet at once.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from Scottsburg, IN
Parts Used:
WPW10380496
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Brush's Wore
Change brush's
Was this instruction helpful to you?
Thank you for voting!
Customer:
andrew from bridgeville, PA
Parts Used:
WPW10380496, W11656718
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
would not run
I just put in the new brushes
Was this instruction helpful to you?
Thank you for voting!
Customer:
Franciska from Carrollton, TX
Parts Used:
WP9704329
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
bent wisk
replace wisk order process very efficient and delivery prompt.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 5KSM180LEABK0
106 - 120 of 189