5KSM180HBSD4 Whirlpool Mixer - Instructions

Neither motor brush popped out with the spring as shown on videos. Both appear to have disintegrated in part and had to be chiseled out delicately using and ice pick and tapping gently with a hammer. This left a carbon powder and pieces of the old brushes on the counter. Inserting the new brushes was as easy as shown on the video.

Unscrewed 3 Philips screws. Pried out the old screw cap. It had been there for 25 years and had flour, egg, etc. build up over the years. Did use a needle nose plier to lift it out. Put in the new one. Needed a rubber mallet to snug it down. Design has changed slightly over the years. Put the 3 screws back in and as they say in England, "you have an uncle named Bob."

watched instruction video (from Part Select), the demonstration was close enough to enable me to repair the mixer. Newer mixers are disassembled differently.

Repair was easy. Remove the seal ring with a flat blade screwdriver and drive out retaining pin. Pry out lower unit using two screwdrivers, one on each side. Once apart, use spring clip pliers to remove snap ring. Pull out shaft and replace. Clean and lubricate as you reassemble in reverse. Google the model number to get detailed instructions.

I was very happy with the customer services department and the support I received in identifying the part I needed for the repair. I received an email confirming my order with all details. I do wish you had a more cost effective shipping alternative, like Priority mail.
The repair went well and the mixer is back in business, for making those Chocolate Chip Cookie and brownies if you know what I mean.

Thank you
Ron Ashby

Opened beater , removed grease , took bearing off , removed alignment pins ,pulled shaft and pinion out , replaced parts , lubricated with new grease , assembled the whole drive . do not like the plastic gear or the clearance once assembled has a lot of slop for this type of drive .

The brushes on the inside of the motor were destroyed. We thought that it would be easier to just replace the brush holder and the brushes, however, the brushes were easy! and QUICK! The brush holders...not so much. We had lots of problems getting the brush holders into place because of a metal piece that had to fit perfectly on top of the brush holder. It made it easier when I held the mixer upside down (we dissembled it) and my husband did his magic on fixing the brush holders. Pray that you won't need to replace the brush holders because it was NO FUN...but the brushes were QUICK AND EASY :)

Replaced electrical board and speed control plate. cleaned and added new grease. Removed agitator cover and replaced agitator with new. Problem agitator did not match existing. Old agitator was drilled and tapped for a plate to hold gear in place. Tried one without does not work.

I watched the video twice and made the repairs

i followed the instructions in video. Thank you joe

Wish that I had known about the video before disassembling. I did not know if it needed a part or was just jammed. It was clear that i needed a worm gear. So I ordered that. It turned out that I needed the Pinion Shaft w/ gear too. So another order. The shipping far exceeded the cost of the parts. NOTE: Clear off as much grease as necessary to be certain that there are no stripped gears anywhere, the order the parts. I took the mixer head off of the stand. I would suggest that you take a bath towel, roll each end towards the center, and place the mixed head so that it is supported on both sides by the towel rolls. NOTE2: Shipping was great 2 days or less. One part arrived on a Saturday. P>S> I do not know the age of this mixer. The age drop down menu should have an UNKNOW option.

Followed directions video on line. good directions.

Took it to repair shop

Easy removal of old screw cap, but new one didn't just drop in. Had to scrape paint and a little aluminum to make it fit. Finally did, and it works fine now.

After I dropped a part of the shield into my mixer the motor screamed and I unplugged the mixer. I found out I had a broken worm gear. I then order the part and per the helpful video I did the repair and I also changed the brushes my mixer is up and running waiting for the holiday baking season thanks to Part select.com Very easy Instructions to follow I am very happy with the results. Thanks Barbara