KL26M2XER5 Whirlpool Mixer - Instructions

We are a pretty handy bunch here. However, the diagrams provided with the part numbers did assist in the disassembly. It went smooth and easy.

Looked at the schematic for this model on Parts Select. Removed Aluminum band screw, removed the 4 screws that hold the top of the mixer. Lifted the top off. Removed 4 screws and lifted the gear case. Removed snap ring and took off tapered gear. Removed pin and removed worm gear. Picked out the metal, in the grease, from the old worm gear, using a magnet then inserted new worm gear and put it back together in reverse order. There was plenty of grease and didn't need to add any.

I have to thank you at Partselect.com. You happen to help me help other people. Now I have several people bringing me their Kitchenaids to me instead of sending them in. I replaced two worm gears on a Kitchenaid 6 and the Hall sensor on a Kitchenaid 5. Very easy to do. Next week I have another Kitchenaid 5 to replace the motor on. Thankyou again for having the parts I need

Remove screw and nut from back of mixer head to release the silver name band. Remove the exposed four cross head screws, (two each side), and lift off the motor and gear cover. Wipe excess grease from gear wheels to expose the retaining ring clip at top of vertical gear shaft. Using small nose circlip pliers, remove retaining ring and bevel gear wheel to expose shaft pin and worm gear. Support the shaft from below and remove pin. Lift off worn worm gear wheel allowing shaft to drop down. The horizontal worm gear shaft can now be lifted out taking care to keep assembled. Carefully clean old grease from all gears and from the gear housing, (note that broken pieces of the old worm gear are in the old grease. Repack housing with fresh high performance grease recommended for worm drives. Cover new and reuseable gears with grease. Reverse the process to reassemble the unit.

___ Remove silver decorative band/1 screw ___ Remove top of mixer/4 screws ___ Remove circuit board/2 screws ___ remove 5 wires from ckt. bd. (be sure where they go) ___ Install new ckt. bd. with proper electircal connections ___ test mixer/OK ___ Reassemble & retest/OK

Following Replacement Part Youtube instructions, I disassembled the mixer and found what caused the sounds and prevented the mixer from operating. The worm follower gear had been ground down by the worm gear. I found that the shaft from the planetary gear had not been adequately greased and siezed preventing the worm follower gear from turning. The worm gear is obviously made of harder material and thus, was able to wear away the follower. I appreciate the your help which saved having to replace a perfectly good/expensive mixer. Thanks.

opened the mixer.. all screws in kitchaid are the same so not to worry... opened up and replaced the gears... and put it back together... diagram helped in that front and rear bearings of connecting gear are the same # on diagram it is easy to confuse when you put it back together, but the item number and description of each helped make sure it was in the right place. Otherwise... time to fix would have been less....

took mixer cover off, took gear box cover off, removed gears, replaced gears, replaced covers, made cookies, no problem!!

I sent for a new thumb screw and screwed it in where it belongs and now I can use my other attachments.

I replaced the switch component twice and I still have the same problem. I will purchase a new motor now see if that works? I'll post what happens thanks

took off the strap band around mixer, took off the cover (4 screws, took off gear cover (4 screws) took off the retaining ring(used pliers and screwdriver) took off upper gear, took out retaining pin, took off lower gear (becareful to grab the planetary assembly as it will fall out after you take out the retaining pin) cleaned out all of the gear grease (the teeth that were missing were in it. replaced the planetary assembly, lower gear and retaining pin. replaced the upper gear, replaced the retaining ring (used screwdriver and hammer. you have to spread the ring with end of screw driver so it will fit on the shaft then tap lightly with screwdriver and hammer to get it down to the keyway for the ring.) replaced the gear grease with NEW grease, reaplaced the gear cover, replaced the mixer cover, replaced the strap band and plugged it in to test it. IT was quieter than before and works great. i spent less than $30 to repair my 10 year old, out of warranty, Kitchen Aid Mixer. much better than the $32.00 to ship it to factory repair shop and get an estimate to repair. I needed it to make a cake for my nephews wedding. I had my parts in 2 DAYS!!! it was a great experience over all.

I had previously ordered several other gears after I found one of the worm gears stripped. After putting it all back together, the one major gear in the unit that I had not replaced because it looked fine, the bevel gear, also stripped. Learning experience: this is a unit worth several hundred dollars, so don't skimp on a $4 part. Once you work on this thing, you might as well spend a few bucks more and replace ALL the gears - even if they look like they are okay. Furthermore, if you only take 15 minutes to do this repair, as some on this site suggest, you are probably not cleaning the old grease carefully enough. Make sure you properly clean out the old grease to remove any metal from stripped gears, and use a good quality grease to re-pack the gear case.

First and foremost, I am not mechanical at all. I typically refer to parts as thing-a-ma-jigs, and whatca-ma-call-its. When it froze up and started to make a loud grinding noise, I guessed it was a gear problem. I decided to try to take it apart, What did I have to lose? If I couldn't figure it out, I would be down a mixer. I was already down one as it was. It was very easy to take apart and I could immediately see what gears needed to be replaced. Parts Select made it very easy to see what parts I needed. And delivery was lightning fast; the next day after it shipped! I found a PDF on line on how to dis-assemble and re-assemble the mixer. I got it together and it mixed for a few minutes and froze again. I took it apart and realized that I didn't have the whatcha-ma-call-it (worm gear) seated properly. Fixed it and put it back together and put it to the test. Working just fine now! Thank you Parts Select for making this very easy!

Ordered new worm gear and received in a few days. I cleaned out old grease from the gear housing, replaced the worm gear and packed with new grease. Machine runs well now. Easy repair.

replaced planetary assembly. Was not difficult to do.