5KSM165PSCGU0 Whirlpool Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tiffany from San Antonio, TX
- Parts Used:
- WP16910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Pin fell out of neck
Placed pin in the hole...some wiggling had to be done for a tight fit. Installation complete!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Belle Fourche, SD
- Parts Used:
- WPW10674618
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the dough hook was chipped
replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Lynden, WA
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Thumb screw
the plastic covering the thumb screw cracked almost half way and lost the piece....so the new one is being used to replace this old one...very easy to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Miya from Seattle, WA
- Parts Used:
- W11544572
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Base lost grip
Put on a new base plate using fresh screws, all ordered on Parts Select in under a minute. Now my grandmas old Kitchen Aid Stand-up mixer is as good as new! This was way easier than I thought it would be and really a great experience!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Craryville, NY
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wire whip brokrn
Just screwed it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from Tracy, MN
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic worm gear stripped
The plastic worm gear was stripped,I took it apart first then cleaned out all the old grease so when the new part came it together like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jennie from cupertino, CA
- Parts Used:
- WPW10674618
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost dough hook so no repair
Just put it on and my challah was perfect!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alvaro from Brighton, CO
- Parts Used:
- WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Worm gear was bad
Order part through parts select. it only took 3 days to receive part. The mixer was very easy to take apart and to replace the gear. it was back together in about 20 min. The video from kitchen aid to repair the unit is awsome. Thanks
Was this instruction helpful to you?
Thank you for voting!
Replaced main gears
1. Removed the mixer from the base by removeing the pivot pin at the mixer base support. 2. removed the retainer ring from the housing. 3. removed the pin from the shaft. 4. removed 5 philips machine screws from the round base. 5. removed the round base from the mixer housing. 6. removed the o-ring from the shaft. 7. removed the shaft and large worm/pinion gear from the shaft. 8. pressed out the pinion drive gear from the mixer. The reverse operation repaired the mixer to new condition.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nick from Naperville, IL
- Parts Used:
- WPW10380496
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My wife was complaining of a loud grinding noise.
I replaced the brushes. I didn't realize that I've put one of them wrong. Reminder for next time the brushes have to touch the rotor of the motor. It took me a little bit to understand but the brushes can go in and not touch the rotor. It works very quietly now. Thank you PartSelect for your infos and knowledge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Fairfax, VA
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mixer bowl was slipping off the base when in use
Replacing the base retaining bracket(what KitchenAid calls the screw cap) solved the problem immediately. The entire replacement effort took no more than a minute requiring removing 3 screws, discarding the old base, putting in the new one, and putting the screws back in. PartSelect was very easy to do business with. They shipped the part the day I ordered it and it arrived as scheduled. Can't be easier than that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Franciska from Carrollton, TX
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bent wisk
replace wisk order process very efficient and delivery prompt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Takahiro from Arlington, MA
- Parts Used:
- WPW10380496
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Food mixer suddenly stopped without burnning smell
Just change the motor brush. That's it! It work well now. Thank you, Partselect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from St. Cloud, WI
- Parts Used:
- WP116287
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new brushes for a mixer
Easy to locate part I needed (brushes)..great diagrams Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Aitkin, MN
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Screw cap or retainer wore out and wouldn't hold the bowl tight
Removed the old screw cap and installed the new one-only has 3 screw to remove and re install. VERY easy. Fits perfectly
Was this instruction helpful to you?
Thank you for voting!